Orange pi zero 2 board can not boot ..
Hi ..Yesterday i have received the orangepi zero 2 board. I have tried with 3 different microsdcards .. and the results are the same.
Only in android image and using PhoenixCard app i can see the boot process from the serial port.
I am using a 5V 2A power supply.
Microsd cards .. 2GB, 4GB, and 64 gb transcend and Sandisk.
Here you have the boot output when using android image :
U-Boot 2018.05 (Oct 22 2020 - 17:24:26 +0800) Allwinner Technology
CPU: Allwinner Family
Model: sun50iw9
I2C: ready
DRAM:1 GiB
Relocation Offset is: 35ec5000
secure enable bit: 0
pmu_axp152_probe pmic_bus_read fail
PMU: AXP806
PMU: pmu_axp806 found
dcdce_vol = 3300, onoff=1
aldo1_vol = 3300, onoff=1
bldo1_vol = 1800, onoff=1
CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100MhzMBus=400Mhz
init_clocks:finish
drv_disp_init
HDMI 2.0 driver init start!
__clk_enable: clk is null.
hdmi cec clk enable failed!
drv_disp_init finish
gic: sec monitor mode
boot_gui_init:start
CEA VIC=16: 1920x1080p@60 Hz 16:9, 8-bpp YCbCr-444
BT709
eotf:SDR_LUMINANCE_RANGE
switch device: sel=0, type=4, mode=10, format=1, bits=0, eotf=4, cs=257
boot_gui_init:finish
flash init start
workmode = 17,storage type = 1
try card 2
set card number 2
get card number 2
mmc driver ver uboot2018:2019-12-13 9:48:00
get mem for descripter OK !
Set eMMC Power Mode to 1.8V!
card2 io is 1.8V.
get card2 disable pin fail
get sdc_ex_dly_used 2, use auto tuning sdly
get sdc_ex_dly_used 2, use auto tuning sdly
current is product mode, it will tune sdly later
get sdc2 sdc_boot0_sup_1v8 fail.
get card-pwr-gpios faild
get card2_boot_para:time_pwroff_ms:use default time_pwroff:200
Is not Boot mode!
io is 1.8V
init mmc 2 clock and io
devnum 2, prv 7ffac860, bdesc 7c28eb6c
SUNXI SD/MMC: 2
==================== work mode: 17 0, sample_mode:2
=============== start mmc_init_product...
=============== start mmc_init_product...
************Try SD card 2************
rto or no error or software timeout,no need retry
rto or no error or software timeout,no need retry
rto or no error or software timeout,no need retry
************Try MMC card 2************
rto or no error or software timeout,no need retry
Card did not respond to voltage select!
************SD/MMC 2 init error!************
mmc init product failed
MMC init failed
try emmc fail
nand common1 version: v1.02 2020-06-08 10:36
NB1 : enter phy init
enter rawnand hardward init..
Reset NDFC start 00
Reset NDFC end 0 0
rawnand not support chip 0: 00 00 00 00 00 00 00 00
rawnand not support chip 1: 00 00 00 00 00 00 00 00
rawnand not support chip 2: 00 00 00 00 00 00 00 00
rawnand not support chip 3: 00 00 00 00 00 00 00 00
no rawnand found!
rawnand_channel_init channel@0 chips init fail
rawnand hardward init fail
---rawnand_dump_clock start---
SUNXI_CCM_BASE: 0x03001000
nand0 clk: 8300010e
nand1 clk: 8300010e
nand bus gating reset: 10001
mbus cfg: c1000002
mbus master clk gating: 25
pll_peri0 ctrl: b8003100
pll_peri1 ctrl: 88003100
---rawnand_dump_clock end---
---rawnand_dump_gpio_nand start---
SUNXI_PIO_BASE: 0x0300b000
pc cfg0: 22222222
pc cfg1: 22222222
pc cfg2 2
pc data: 0
pc drv0_lvl: 55555555
pc drv1_lvl: 1
pc pull_0: 40000440
pc pull_1: 1
voltage mode select: 0
---rawnand_dump_gpio_nand end---
nand_physic_init error -1
NB1 : nand phy init fail
Failed to probe nand flash
try nand fail
initcall sequence 7ff5bee0 failed at call 4a00e1fd (err=-1)
### ERROR ### Please RESET the board ###
Thanks for all ..
Waiting for recommendations ...
Ok. Solved .. I have downloaded armbian for orangepi zero 2. Now works .
Thanks. The armbian version only works via a serial console only...:curse::curse::curse: Please read my post from http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=6147&fromuid=2501169
Finally, after clearing customs, you will need to register your vehicle with the local Department of Motor Vehicles (DMV). Each state has its own registration requirements and fees https://www.youtube.com/watch?v=db-5886oHp4 I appreciate the user-friendly design of my extension ladder, with features like quick-locking mechanisms that allow for easy setup and takedown. read this Confirm that you are pokemon infinite fusion using the correct Android image for your Orange Pi Zero 2 model. Sometimes, images designed for different models might not be fully compatible. Wow, this is really interesting reading. I am glad I found this and got to read it. Great job on this content. I like it. securespend