please choosego to mobile | Continue to access the PC version
View: 18244|Reply: 10

Orange Pi Plus Bugs,featured,etc.

[Copy link]

4

threads

65

posts

260

credits

Intermediate member

Rank: 3Rank: 3

credits
260
Published in 2015-5-12 22:52:12 | Show all floors |Read mode
Edited by wolftronics at 2015-5-25 16:20

Orange Pi Plus H3 Helping
--------------------------------------------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------
Bugs....
1.Temperature now is more than 50 degrees Celsius (About 51-52)  rasbian,debian,lubuntu image     kernel problems!!!???
   Android H3 image youtube playing not hot...
2. no sound jack output rasbian,debian,lubuntu image
     /etc/modules   ????
     Android H3 image ok
3. Installing Mail binary drivers
   http://linux-sunxi.org/Mali_binary_driver
    https://www.olimex.com/forum/index.php?topic=1910.0   
    ~/sunxi-mali# make install                                        make -f Makefile.config
    make[1]: Entering directory '/root/sunxi-mali'
    ABI="armhf" (Detected)
    VERSION="UNKNOWN" (Detected)
    Makefile.config:57: Unknown/unhandled Mali Version "UNKNOWN"
    Makefile.config:58: Use VERSION=(r2p4,r3p0,r3p1,r3p2-01rel1) instead
    Makefile.config:59: *** Unknown/unhandled Mali Version "UNKNOWN".  Stop.
   
   make install VERSION=r3p0    etc...
   test/test
   not work egl/gles driver stack!!!

------------------------------------------------------------------------------------------------
Featured
screen resolution optional   720x576, 1280x720,1980x1080 TV
                             1024x768 1280x1024 4:3 Monitor
server image
      display screen hdmi with no desktop

Android 4.4.2
Bugs....
1. Ethernet Dhcp not work.
2. manual ip "static" work but little buggy displayed configuration. Once showed, then do not.
3. there is a Home on the upper left corner , no Cancel but mouse right click also works , I  cannot find  Menu button on screen or on the board.



Published in 2015-5-12 23:28:16 | Show all floors
1. Linux distribution version need cupfreq.  2. Audio need fix.  3. Need add Mali driver. Please wait for a while.

4

threads

65

posts

260

credits

Intermediate member

Rank: 3Rank: 3

credits
260
 Author| Published in 2015-5-13 01:09:34 | Show all floors
zhao_steven replied at 2015-5-12 23:28
1. Linux distribution version need cupfreq.  2. Audio need fix.  3. Need add Mali driver. Please wai ...

1. Linux distribution version need cupfreq. how to.... "raspi-config" ok?
cpufreq_conservative
cpufreq_ondemand
cpufreq_powersave
cpufreq_userspace

2

threads

10

posts

308

credits

Intermediate member

Rank: 3Rank: 3

credits
308
Published in 2015-5-13 18:23:48 | Show all floors
And shutdown -r not work..... ;)

4

threads

65

posts

260

credits

Intermediate member

Rank: 3Rank: 3

credits
260
 Author| Published in 2015-5-16 17:27:14 | Show all floors
rupertgti replied at 2015-5-13 18:23
And shutdown -r not work..... ;)

probably  http://linux-sunxi.org/Cpufreq

6

threads

116

posts

401

credits

Intermediate member

Rank: 3Rank: 3

credits
401
Published in 2015-5-19 01:38:37 | Show all floors
ok Steven. I know that you will eventually fix those issues and everybody will be happy.

4

threads

65

posts

260

credits

Intermediate member

Rank: 3Rank: 3

credits
260
 Author| Published in 2015-5-19 03:55:29 | Show all floors
OrangePiLinux replied at 2015-5-19 01:38
ok Steven. I know that you will eventually fix those issues and everybody will be happy.

that's why open topic that if we can help our ...;)

1

threads

14

posts

179

credits

Registered member

Rank: 2

credits
179
Published in 2015-5-28 13:25:05 | Show all floors
pi2 with  sdcard android  image :shell command  “reboot ”  may not work ,it  blocks  , I have to power off then power on.

root@dolphin-orangepi-plus:/ # reboot
[ 1029.478526] SysRq : Emergency Remount R/O
[ 1029.483019] The process is "init" (pid 1)
[ 1030.660947] Restarting system.
[ 1030.664411] Restarting Linux version 3.4.39 (allwinner@steven) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #6 SMP PREEMPT Mon Mar 23 14:37:37 HKT 2015
[ 1030.664441]
HELLO! BOOT0 is starting!
boot0 version : 4.0.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x000000e0
rtc[2] value = 0x00000000
rtc[3] value = 0x0000000f
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V0.8
DRAM Type = 3 (2DR2,3DR3,6PDDR2,7PDDR3)
DRAM CLK = 672 MHz
DRAM zq value: 003b3bfb
READ DQS LCDL = 00171717
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2014-12-10 21:20:39
[mmc]: ***Try SD card 0***
[mmc]: SD/MMC Card: 4bit, capacity: 29476MB
[mmc]: vendor: Man 00035344 Snr 00b115dd
[mmc]: product: SL32G
[mmc]: revision: 8.0
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
ERROR! NOT find the head of uboot.
The size of uboot is 000dc000.
sum=264121ac
src_sum=257721ac
Fail in checking uboot.
read all u-boot blk failed
Ready to disable icache.


HELLO! BOOT0 is starting!
boot0 version : 4.0.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V0.8
DRAM Type = 3 (2DR2,3DR3,6PDDR2,7PDDR3)
DRAM CLK = 672 MHz
DRAM zq value: 003b3bfb
READ DQS LCDL = 001c1c1d
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2014-12-10 21:20:39
[mmc]: ***Try SD card 0***
[mmc]: SD/MMC Card: 4bit, capacity: 29476MB
[mmc]: vendor: Man 00035344 Snr 00b115dd
[mmc]: product: SL32G
[mmc]: revision: 8.0
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
ERROR! NOT find the head of uboot.
The size of uboot is 000dc000.
sum=257721ac
src_sum=257721ac
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
SUNXI_NORMAL_MODE   
[      0.367]e mode

U-Boot 2011.09-rc1 (Mar 13 2015 - 12:54:51) Allwinner Technology

[      0.374]version: 1.1.0
normal mode
[      0.382]pmbus:  ready
not set main pmu id
axp_probe error
[      0.397]PMU: pll1 1200 Mhz,PLL6=600 Mhz
AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[      0.427]DRAM:  1 GiB
relocation Offset is: 35af9000
[box standby] read rtc = 0x0
[box_start_os] mag be start_type no use
user_gpio config
user_gpio ok
gic: normal or no secure os mode
workmode = 0
MMC:    0
[      0.502][mmc]: mmc driver ver 2014-12-10 9:23:00
[      0.507][mmc]: get sdc_phy_wipe fail.
[      0.511][mmc]: get sdc0 sdc_erase fail.
[      0.515][mmc]: get sdc_f_max fail,use default 50000000Hz
[      0.520][mmc]: get sdc_ex_dly_used fail,use default dly
[      0.526][mmc]: SUNXI SD/MMC: 0
[      0.539][mmc]: *Try SD card 0*
[      0.588][mmc]: CID 0x3534453 0x4c333247 0x8000b115 0xdd00f4b3
[      0.593][mmc]: mmc clk 50000000
[      0.597][mmc]: SD/MMC Card: 4bit, capacity: 29476MB
[      0.602][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB
[      0.607][mmc]: ***SD/MMC 0 init OK!!!***
[      0.612][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte
[      0.617][mmc]: secure_feature 0x0
[      0.621][mmc]: secure_removal_type  0x0
[      0.625]sunxi flash init ok
script config pll_de to 864 Mhz
Not Found clk pll_video1 in script
script config pll_video to 297 Mhz
[boot]disp_init_tv
[DISP_TV] disp_init_tv enter g_tv_used
screen 0 do not support TV TYPE!
[BOOOT_DISP_TV] disp tv device_registered
unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
enable power vcc-hdmi-18, ret=-1
DRV_DISP_Init end
boot_disp.auto_hpd=1
auto hpd check has 50 times!
read byte = 10
[get_display_resolution] = 20b
get the output mode from android(saved by type[2]) is 11
attched ok, mgr1<-->device1, type=2, mode=11----
ready to set mode
disp_tv_enable
[      1.470]finally, output_type=0x2, output_mode=0xb, screen_id=0x1, disp_para=0x20b0000
In:    serial
Out:  serial
Err:  serial
--------fastboot partitions--------
-total partitions:14-
-name-        -start-      -size-      
bootloader  : 1000000      1000000     
env        : 2000000      1000000     
boot        : 3000000      1000000     
system      : 4000000      30000000   
misc        : 34000000      1000000     
recovery    : 35000000      2000000     
sysrecovery : 37000000      30000000   
private    : 67000000      1000000     
Reserve0    : 68000000      1000000     
klog        : 69000000      1000000     
Reserve1    : 6a000000      2000000     
Reserve2    : 6c000000      1000000     
cache      : 6d000000      28000000   
UDISK      : 95000000      0           
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
misc partition found
to be run cmd=run setargs_mmc boot_normal
[      1.580][mmc]: MMC Device 2 not found
[      1.584][mmc]: Can not find mmc dev
[      1.587][mmc]: read first backup failed in fun sdmmc_secure_storage_read line 1849
sunxi_secstorage_read fail
get secure storage map err
the user data'magic is bad
WORK_MODE_BOOT
adver not need show
sunxi_bmp_logo_display
f_read btr over hd12896
read byte = 3686456
[      1.791]screen_id =1, screen_width =720, screen_height =576
[      1.796]frame buffer address 46400000
[      1.800]Hit any key to stop autoboot:  0
read boot or recovery all
[      2.346]sunxi flash read ffset 3000000, 12981523 bytes OK
[      2.354]ready to boot
board_display_setenv:  disp_para=20b0000
[      2.360][mmc]: MMC Device 2 not found
[      2.364][mmc]:  mmc  not find,so not exit
[      2.368]
Starting kernel ...

[sun8i_fixup]: From boot, get meminfo:
        Start:  0x40000000
        Size:  1024MB
ion_carveout reserve: 160m@0 256m@0 130m@1 200m@1
ion_reserve_common: ion reserve: [0x70000000, 0x80000000]!
[    0.392554] can't get item for emac_power gpio !
[    0.649556] ls_fetch_sysconfig_para: type err  device_used = -427573448.
[    0.657904] tscdev_init: tsc driver is disabled
[    0.664531] [cpu_freq] ERR:get cpu extremity frequency from sysconfig failed, use max_freq
[    0.691952] sunxi_oops: heming add OOPS_INFO_ADDR = -20
[    0.742123] ths_fetch_sysconfig_para: type err  device_used = 1.
[    0.756538] init: /init.rc: 168: invalid option 'setprop'
[    0.800471] init: open path: /dev/bus/usb/001/001
[    0.980720] init: open path: /dev/bus/usb/002/002
[    1.181009] init: open path: /dev/bus/usb/002/001
[    1.330199] init: open path: /dev/bus/usb/002/002
[    1.530126] init: open path: /dev/bus/usb/002/003
[    1.800462] init: open path: /dev/bus/usb/002/003
[    2.064324] init: open path: /dev/bus/usb/003/001
[    2.220947] init: open path: /dev/bus/usb/004/001
[    2.386324] init: /dev/hw_random not found
[    2.391173] init: defined DONT_SHOW_INITLOGO
[    2.551665] init: start e2fsck listening...
[    3.066786] init: dont need format /dev/block/by-name/private
[    3.256742] Failed to get mali parameter!
[    3.463124] [SPDIF]sunxi-spdif cannot find any using configuration for controllers, return directly!
[    3.490422] [SPDIF]sndspdif cannot find any using configuration for controllers, return directly!
[    3.556281] init: C_IN_START
[    3.559365] init: path = /dev/block/by-name/cache
[    3.564668] init: C_IN_START
[    3.567897] init: path = /dev/block/by-name/UDISK
[    3.679080] init: /dev/hw_random not found
[    3.695467] healthd: Could not open /sys/class/power_supply
[    3.697535] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[    3.711102] healthd: No charger supplies found
[    3.811566] android_usb: already disabled
[    3.816278] init: using deprecated syntax for specifying property 'sys.usb.config', use ${name} instead
[    3.827430] init: using deprecated syntax for specifying property 'sys.usb.config', use ${name} instead
root@dolphin-orangepi-plus:/ # [  15.010206] init: sys_prop: permission denied uid:1003  name:service.bootanim.exit
[  17.078111] qtaguid: iface_stat: stat_update() wlan0 not found

2

threads

9

posts

59

credits

Registered member

Rank: 2

credits
59
Published in 2015-5-28 17:25:36 | Show all floors
On the Orange Pi Plus, using Raspbian, I see in dmesg:

[   22.550148] ==> rtl8188e_iol_efuse_patch
[   22.785144] RTL871X: nolinked power save leave
[   24.090085] RTL871X: nolinked power save enter
[   24.410027] eth0: no IPv6 routers present
[   29.400240] ==> rtl8188e_iol_efuse_patch
[   29.635148] RTL871X: nolinked power save leave
[   30.940048] RTL871X: nolinked power save enter
[   36.250144] ==> rtl8188e_iol_efuse_patch
[   36.486157] RTL871X: nolinked power save leave
[   37.790049] RTL871X: nolinked power save enter
[   43.100173] ==> rtl8188e_iol_efuse_patch

It keeps going like that.

Also core 3 always gets disabled after a while:
root@orangepi:~# grep . /sys/devices/system/cpu/cpu*/online
/sys/devices/system/cpu/cpu0/online:1
/sys/devices/system/cpu/cpu1/online:1
/sys/devices/system/cpu/cpu2/online:1
/sys/devices/system/cpu/cpu3/online:0

Which is also reflected in /proc/cpuinfo.

Does anybody know a step-by-step method to change the resolution and how to read out (+ interpret, if not in celcius) the CPU temp?

If it's not possible in Raspbian, is it possible in another distro?

Should I order a heat sink (because the H3 chip get's hot really fast)?

0

threads

3

posts

22

credits

Novice

Rank: 1

credits
22
Published in 2016-1-20 20:23:07 | Show all floors
Hello, same error with Temperature, how can i read it from builtin CPU sensor?
under Debian or any same...

You need to log in before you can reply login | Register

Points Rule

Quick reply Top Return list