please choosego to mobile | Continue to access the PC version
View: 19801|Reply: 18

My orange pi plus can't connect sata hdd.

[Copy link]

11

threads

53

posts

1254

credits

Gold member

Rank: 6Rank: 6

credits
1254
Published in 2015-5-23 20:40:21 | Show all floors |Read mode
Edited by garyang at 2015-5-27 17:52

I received sata/power cable yesterday.
(like this :http://www.aliexpress.com/item/R ... 2010308.4.20.oXhpii)
I've tried to connect to orange pi plus, It does not seem to be working .
I tested both ext3 and ext4 partition. I used Raspbian and Debian Server.
I also connected sata data cable and power cable separately.
but, useless.....T.T...

Here is part of dmesg

[   12.461140] scsi 1:0:0:0: Direct-Access     USB TO I DE/SATA Device   0009 PQ: 0 ANSI: 0
[   12.472181] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   12.474870] sd 1:0:0:0: [sda] Test WP failed, assume Write Enabled
[   12.475982] sd 1:0:0:0: [sda] Asking for cache data failed
[   12.475991] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   12.480399] sd 1:0:0:0: [sda] Test WP failed, assume Write Enabled
[   12.481625] sd 1:0:0:0: [sda] Asking for cache data failed
[   12.481634] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   12.481643] sd 1:0:0:0: [sda] Attached SCSI disk
[   15.788932] ehci_irq: highspeed device disconnect
[   15.789042] usb 3-1: USB disconnect, device number 3
[   16.631872] gmac0: probed
[   16.634919] gmac0 gmac0: eth0: eth0: PHY ID 001cc915 at 0 IRQ poll (gmac0-0:00)
[   16.691932] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   18.451729] ehci_irq: highspeed device connect
[   18.660268] ehci_irq: highspeed device disconnect
[   18.720042] usb 3-1: new high-speed USB device number 4 using sunxi-ehci
[   18.790048] hub 3-0:1.0: unable to enumerate USB device on port 1
[   18.796811] ehci_irq: highspeed device disconnect
[   21.265379] ehci_irq: highspeed device connect
[   21.487548] ehci_irq: highspeed device disconnect

Is this Kenel problem or sata port was broken?
If it is the case that SATA port problem, I have to request a replacement.

Is anybody successful sata port connected to pi plus?

4

threads

65

posts

260

credits

Intermediate member

Rank: 3Rank: 3

credits
260
Published in 2015-5-23 21:04:17 | Show all floors
it works for me ...
2.5 "hard disk to be 5v !!!
3.5 "hard disk to be 5v 12v !!!

I made him quickly cord ....

[512519.352978] scsi1 : usb-storage 3-1:1.0
[512520.352584] scsi 1:0:0:0: Direct-Access     TOSHIBA  MK3259GSX        0009 PQ: 0 ANSI: 0
[512520.363837] sd 1:0:0:0: Attached scsi generic sg0 type 0
[512520.364431] sd 1:0:0:0: [sda] 625142444 512-byte logical blocks: (320 GB/298 GiB)
[512520.365442] sd 1:0:0:0: [sda] Write Protect is off
[512520.365452] sd 1:0:0:0: [sda] Mode Sense: 03 00 00 00
[512520.366430] sd 1:0:0:0: [sda] No Caching mode page present
[512520.366439] sd 1:0:0:0: [sda] Assuming drive cache: write through
[512520.369918] sd 1:0:0:0: [sda] No Caching mode page present
[512520.369927] sd 1:0:0:0: [sda] Assuming drive cache: write through
[512520.433401]  sda: sda1 sda2 < sda5 sda6 >
[512520.441561] sd 1:0:0:0: [sda] No Caching mode page present
[512520.447798] sd 1:0:0:0: [sda] Assuming drive cache: write through
[512520.454776] sd 1:0:0:0: [sda] Attached SCSI disk


11

threads

53

posts

1254

credits

Gold member

Rank: 6Rank: 6

credits
1254
 Author| Published in 2015-5-23 21:18:54 | Show all floors
wolftronics replied at 2015-5-23 21:04
it works for me ...
2.5 "hard disk to be 5v !!!
3.5 "hard disk to be 5v 12v !!!

Which image did you use for orange pi plus?

4

threads

65

posts

260

credits

Intermediate member

Rank: 3Rank: 3

credits
260
Published in 2015-5-23 21:37:48 | Show all floors
should not be to expect ... debian for a server image raspbian only other packages ...
all have the same kernel.

I tested Debian server image.

11

threads

53

posts

1254

credits

Gold member

Rank: 6Rank: 6

credits
1254
 Author| Published in 2015-5-24 13:27:39 | Show all floors
wolftronics replied at 2015-5-23 21:37
should not be to expect ... debian for a server image raspbian only other packages ...
all have the  ...

I see.
I also tested it on android.
It doesn't work too.
Clearly, It's H/W problem.
I have to ask to change it.
Thanks for your reply~~~

9

threads

634

posts

4398

credits

Moderator

Rank: 7Rank: 7Rank: 7

credits
4398
Published in 2015-5-24 16:46:30 | Show all floors
I also tested it on android.
It doesn't work too.
Clearly, It's H/W problem.


Speaking generally. SATA support in stock Android is usually more by accident not by default.

What about some other hard drive and different power supply?

4

threads

65

posts

260

credits

Intermediate member

Rank: 3Rank: 3

credits
260
Published in 2015-5-24 18:03:17 | Show all floors
garyang replied at 2015-5-24 13:27
I see.
I also tested it on android.
It doesn't work too.

SATA works perfectly under android. Tested !!!

11

threads

53

posts

1254

credits

Gold member

Rank: 6Rank: 6

credits
1254
 Author| Published in 2015-5-25 09:01:44 | Show all floors
igorpec replied at 2015-5-24 16:46
Speaking generally. SATA support in stock Android is usually more by accident not by default.

Wha ...

I've tried 3 kind of HDD 2.5(5400rpm-slim), 2.5(5400rpm), 3.5(5900rpm).
I've also tried change cable.
I've also tried data cable and power cable seperatly  as blow.
I bought 5V/3A DC Adapter for direct power supply.
I spent 2days for this problem.....T.T

This thread contains more resources

You need to Log in to download or view,No account?    Register

x

11

threads

53

posts

1254

credits

Gold member

Rank: 6Rank: 6

credits
1254
 Author| Published in 2015-5-27 17:59:50 | Show all floors
I've solved this problem partially.
I purchased Sata cable that is compatible cubie board.
The cubie sata cable is connected to the power had been opposed to each other .(+, - reversed)
That's my problem.
I pulled out connecter and reverse it.
Now My Sata cable works like cham....^.^
but Independent connection of the power supply and the data is still not working.

11

threads

53

posts

1254

credits

Gold member

Rank: 6Rank: 6

credits
1254
 Author| Published in 2015-5-27 18:02:15 | Show all floors
garyang replied at 2015-5-23 21:18
Which image did you use for orange pi plus?

How can you connect 3.5 HDD?
Would you like me to explain in more detail ?
You need to log in before you can reply login | Register

Points Rule

Quick reply Top Return list