login|Register
Forum > Beginners
Post|
OPi One images
看6438|回5|Favorite
Matt_Edwards 看全部
2016-12-12 08:20:36
Hi,
Firstly let me say I am a newby and will ask forgiveness now if I should say something stupid.

My set up is:
5v 8Amp  power supply ( this is a SMPS I had available)
USB Voltage monitor connected
USB Keyboard Mouse Combo


I have been loading images on to a couple of 8G Micro SD cards and then observing the result.
Imager software
SequenceOS ImagePhoenix Card 3.1.0 Etcher v1.0.0-beta.17Result / Observations
1sun8iw7p1_android_orangepi_pc_uart0_v0.8.0Yes1. Red LED On,   
    2. Green Led On then Off after about 5 seconds,
    3. Screen shows H3 Quad Core logo then disappears after about a  minute
    4. SSH not possible after 5 minutes - error message "Network  connection refused"
    5. after 25minutes screen with space image and Chineese text flashed. top  right corner shows network connectivity icon, Mouse and keyboard not  recognised
    6. still can't SSH to OPIOne  
    7. Screen flashes blank and then home page.   Powered down after 40 minutes
2Armbian_5.14_Orangepione_Debian_jessie_3.4.112_desktopYes1. No Red LED, Screen  blank
    2. No change after 5 minutes
    3. Powered down after 10 minutes
3pcDuino4STB_android_H3_4.4_8188-20150608.imgYes1. Red LED Turns On, Screen  shows "Android TV box"
    2. No Lan activity LED
    3. Powered down after 15 minutes and no change
4Armbian_5.20_Orangepione_Debian_jessie_3.4.112Yes1. No Red LED, Screen blank,  Green LAN activity LED flashes
    2. No change after 5 minutes
    3. Powered down after 15 minutes
5Lubuntu_1404_For_OrangePiPC_v0_8_0_.imgYes1. Red LED turns On
    2. Screen Blank
    3. No Lan activity LED
    4. powered Down after 60 minutes
6OrangePI_Ubuntu_Vivid_Mate.imgYes1. Red LED turns On
    2. Screen Blank
    3. No Lan activity LED
    4. Powered Down after 20 minutes
7Raspbian_For_OrangePi_PC_v0_8_0.imgYes1. Red LED turns On
    2. Screen Blank
    3. No Lan activity LED
    4. Powered Down after 20 minutes
9Volumio1.5_for_OrangePi_v0.2.imgYes
8OpenELEC-H3.arm-7.0-devel-20161026221335-r23113-g64b34b3-opione.imgYes1. Red LED stays Off
    2. Screen goes in to Power Saving mode
    3. Lan activity LED flashed
Powered downafter30minutes   


As shown above my success rate sucks.  I monitor the USB voltage and noticed it is usually 5volts but it dips down to 4.8volts occassionly.
I really would like to make this work.  Any distro in english will suffice.
Should monitoring the serial debug port on start up be my next step?

Matt_Edwards 看全部
2016-12-12 09:22:40
I went ahead and added a Serial debug terrminal.

code:


  2. U-Boot SPL 2016.09-armbian (Sep 15 2016 - 07:19:14)
  3. DRAM: 512 MiB
  4. Trying to boot from MMC1


  7. U-Boot 2016.09-armbian (Sep 15 2016 - 07:19:14 +0200) Allwinner Technology

  9. CPU:   Allwinner H3 (SUN8I 1680)
  10. Model: Xunlong Orange Pi One
  11. DRAM:  512 MiB
  12. MMC:   SUNXI SD/MMC: 0
  13. *** Warning - bad CRC, using default environment

  15. In:    serial
  16. Out:   serial
  17. Err:   serial
  18. Net:   phy interface0
  19. eth0: ethernet@1c30000
  20. Hit any key to stop autoboot:  0
  21. switch to partitions #0, OK
  22. mmc0 is current device
  23. Scanning mmc 0:1...
  24. Found U-Boot script /boot/boot.scr
  25. 2886 bytes read in 160 ms (17.6 KiB/s)
  26. ## Executing script at 43100000
  27. gpio: pin PL10 (gpio 298) value is 1
  28.    Warning: value of pin is still 0
  29. gpio: pin PG11 (gpio 203) value is 1
  30. 0 bytes read in 116 ms (0 Bytes/s)
  31. ** File not found /boot/.next **
  32. ** Unrecognized filesystem type **
  33. ** File not found .next **
  34. 35908 bytes read in 430 ms (81.1 KiB/s)
  35. 3114523 bytes read in 326 ms (9.1 MiB/s)
  36. 5025168 bytes read in 473 ms (10.1 MiB/s)
  37. ## Loading init Ramdisk from Legacy Image at 43300000 ...
  38.    Image Name:   uInitrd
  39.    Image Type:   ARM Linux RAMDisk Image (gzip compressed)
  40.    Data Size:    3114459 Bytes = 3 MiB
  41.    Load Address: 00000000
  42.    Entry Point:  00000000
  43.    Verifying Checksum ... OK
  44. Using machid 0x1029 from environment

  46. Starting kernel.....


Is this what I should expect?
igorpec 看全部
2016-12-12 16:08:46

code:

  1. gpio: pin PL10 (gpio 298) value is 1
  2.    Warning: value of pin is still 0
  3. gpio: pin PG11 (gpio 203) value is 1


This is suspicious ... would need to check.

You have nothing after "Starting kernel" ?

Can you edit .env or boot.cmd and set verbosity to 9 and try again. If you edit boot.cmd you need to convert it to boo.scr ...
Matt_Edwards 看全部
2016-12-13 05:07:00
I suspect i have two issues:
I was using two different SD cards and I think one may be faulty or non optimal.  I accidentally removed it without powering it down and thought nothing of it. I will source a couple more today.  I have since got the  Armbian_5.20_Orangepione_Debian_jessie_3.4.112 to load.  
The other issue may be temperature.  I swapped OPI One boards and is loaded immediately.  I notice the H3 on the first board felt too hot. it was uncomfortable to hold my finger on it.  Today I will source a heatsink glue to stick an aluminium heat sink on the H3 chip.

The investigation continues and I will re-run the above image attempts when I get new hardware
Matt_Edwards 看全部
2016-12-13 17:09:36

quote:

igorpec replied at 2016-12-12 16:08
This is suspicious ... would need to check.

You have nothing after "Starting kernel" ?

It appears I have a dead OPI One.  New SD card don't change the situation help.
I loaded Armbian_5.20_Orangepione_Debian_jessie_3.4.112 on a new Micro SD card.  
On boot up the following was output from the debug port:

code:

  1. Terminal log file
  2. Date: 13/12/2016 - 8:01:41 PM
  3. -----------------------------------------------

  5. U-Boot SPL 2016.09-armbian (Sep 15 2016 - 07:19:14)
  6. DRAM: 512 MiB
  7. Trying to boot from MMC1


  10. U-Boot 2016.09-armbian (Sep 15 2016 - 07:19:14 +0200) Allwinner Technology

  12. CPU:   Allwinner H3 (SUN8I 1680)
  13. Model: Xunlong Orange Pi One
  14. DRAM:  512 MiB
  15. MMC:   SUNXI SD/MMC: 0
  16. *** Warning - bad CRC, using default environment

  18. In:    serial
  19. Out:   serial
  20. Err:   serial
  21. Net:   phy interface0
  22. eth0: ethernet@1c30000
  23. Hit any key to stop autoboot:  0
  24. switch to partitions #0, OK
  25. mmc0 is current device
  26. Scanning mmc 0:1...
  27. Found U-Boot script /boot/boot.scr
  28. 2886 bytes read in 143 ms (19.5 KiB/s)
  29. ## Executing script at 43100000
  30. gpio: pin PL10 (gpio 298) value is 1
  31.    Warning: value of pin is still 0
  32. gpio: pin PG11 (gpio 203) value is 1
  33. ** File not found /boot/.verbose **
  34. ** File not found /boot/.next **
  35. ** Unrecognized filesystem type **
  36. ** File not found .next **
  37. 35908 bytes read in 405 ms (85.9 KiB/s)
  38. 3114523 bytes read in 307 ms (9.7 MiB/s)
  39. 5025168 bytes read in 451 ms (10.6 MiB/s)
  40. ## Loading init Ramdisk from Legacy Image at 43300000 ...
  41.    Image Name:   uInitrd
  42.    Image Type:   ARM Linux RAMDisk Image (gzip compressed)
  43.    Data Size:    3114459 Bytes = 3 MiB
  44.    Load Address: 00000000
  45.    Entry Point:  00000000
  46.    Verifying Checksum ... OK
  47. Using machid 0x1029 from environment

  49. Starting kernel ...


  52. -----------------------------------------------
  53. Date: 13/12/2016 - 8:02:04 PM
  54. End log file


It has the same suspission code.  I also confirm there is nothing after Starting kernel.

BTW I also checked the new SD card in the other OPIOne that I got working.

12NextPage

OrangePi En

Powered by Discuz! X3.4

homepage|Simple edition|Touch edition|PC