please choosego to mobile | Continue to access the PC version
Author: loboris

Linux Distributions for Orange PI H3 boards

  [Copy link]

0

threads

1

posts

22

credits

Novice

Rank: 1

credits
22
Published in 2016-2-7 06:15:09 | Show all floors
Hi.
Faced with a problem, I can not raise a raid5.
By long suffering could figure out what it is because it is not loaded kernel module "raid456".
When you try to load it "modprobe raid5" error occurs.

  1. ERROR: could not insert 'raid456': Unknown symbol in module
Copy code


With raid1, raid0, reid10 is loaded with no errors.

Orange pi Plus,
The error occurs in the distributions "orangepi-plus-debian-server-card-v0.9.img" and "OrangePI_Jessie_Xfce.img"

1

threads

11

posts

104

credits

Registered member

Rank: 2

credits
104
Published in 2016-2-12 03:02:29 | Show all floors
nkk replied at 2016-1-12 08:35
is someone installed transmission-daemon?

Yes, I was try to use it , but external USB (with torrent folder) time to time lost connection with Orange Pi. I change 2 external USB but result was same.

0

threads

7

posts

32

credits

Novice

Rank: 1

credits
32
Published in 2016-2-12 10:15:59 from mobile | Show all floors
how can i set up WiFi dongle on OPI pc with android??

0

threads

7

posts

32

credits

Novice

Rank: 1

credits
32
Published in 2016-2-12 10:16:18 from mobile | Show all floors
i am a beginner

0

threads

4

posts

111

credits

Registered member

Rank: 2

credits
111
Published in 2016-2-12 10:31:35 | Show all floors
Do we know if hardware watchdog support is available in this kernel??

3

threads

60

posts

258

credits

Intermediate member

Rank: 3Rank: 3

credits
258
Published in 2016-2-12 16:18:02 | Show all floors
zcat /proc/config.gz prints running kernel configuration

0

threads

4

posts

111

credits

Registered member

Rank: 2

credits
111
Published in 2016-2-12 19:58:10 | Show all floors
zgoda replied at 2016-2-12 16:18
zcat /proc/config.gz prints running kernel configuration

Thanks zgoda
I dont have a config.gz in /proc but dmesg is giving me

[    4.007385] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[    4.019764] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
[    4.031125] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[    4.049212] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
[    4.060848] timeout_to_interv, line 167
[    4.070532] interv_to_timeout, line 189
[    4.080130] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec


so hopefully its actually working.
Now to get the watchdog daemon cooperating with it.




3

threads

7

posts

41

credits

Novice

Rank: 1

credits
41
Published in 2016-2-12 20:55:54 | Show all floors
loboris replied at 2015-9-13 19:13
Tested AP mode, works good using create_ap method.

Before using, install some packages:

hello,
i have a new orange pi plus 2 board when i install kali, fedora or any other distro then it boots up properly but within some amount of time my whole desktop freezes an i m unable to perform any action, it happens with every os i try, i dont undrstand what's the problem please help me.

3

threads

7

posts

41

credits

Novice

Rank: 1

credits
41
Published in 2016-2-12 21:05:35 | Show all floors
hello,
i have a new orange pi plus 2 board when i install kali, fedora or any other distro then it boots up properly but within some amount of time my whole desktop freezes an i m unable to perform any action, it happens with every os i try, i dont undrstand what's the problem please help me.

0

threads

4

posts

111

credits

Registered member

Rank: 2

credits
111
Published in 2016-2-13 08:48:42 | Show all floors
shashisrun replied at 2016-2-12 21:05
hello,
i have a new orange pi plus 2 board when i install kali, fedora or any other distro then it b ...

Sounds a bit like the power supply, try a different one if you can.

You need to log in before you can reply login | Register

Points Rule

Quick reply Top Return list