4G-IOT

orangine · Published in 2018-5-4 01:46:17

orangine replied at 2018-4-28 17:21
Hi Guys,
I've just got the 4G-IOT board and I also got a nice LiPo 3.7V battery. I would like to hoo ...

Anybody? Is there someone from OrangePi checking up some of the posts? Should I post my question somewhere else?

nobotro · Published in 2018-5-4 03:33:30

how root?kingroot and kingoroot not work

lrou · Published in 2018-5-6 20:26:17

Edited by lrou at 2018-5-6 20:34

Hello guys! I've tried to use this orange 4g-iot. After android was installed on the device, I got android desktop that often goes to reboot. Sometimes it cannot boot, in this case I have on hdmi monitor some small display picture with some percentage on it. Is that something wrong with hardware? And anyway, is there any ETA of getting normal linux, say in 6months for example?

jonsmirl · Published in 2018-5-8 09:32:17

lrou replied at 2018-5-6 20:26
Hello guys! I've tried to use this orange 4g-iot. After android was installed on the device, I got a ...

The Android 6 that comes with it is set up for a cell phone sized display. It is running some Mediatek GUI and has not been reworked to enable the standard Android GUI. Personally I am not going to mess with working on this Android 6 and I will wait for the the Android 8 port that is due in a week or two.

I do hope the Android 8 port improves two things:
1) Supports standard 720P and 1080P HDMI modes including DVI which has no HDCP.
2) Boots into the normal Android GUI

For my own project I'd like to see a camera and LCD made available.

birender.s · Published in 2018-5-8 18:21:59

Hello jonsmirl,

Do we able to build using code provided ?

Regards.

jonsmirl · Published in 2018-5-9 01:18:46

The provided Android 6 source does build. It took me a little while to find the ancient Java and tools it needed, but once you find the right tools it does build.
I think it needed java-1.7.0-openjdk-amd64

priapradana · Published in 2018-5-15 11:56:12

Everyone, how i can flashing orange pi 4G-IOT? I follow use guide from http://www.orangepi.org/downloadresources/ and flasing with USB and i make windows 10. Always timeout and never success. What should i do? please.. thanks.

MiXaiLL76 · Published in 2018-5-15 20:54:57

priapradana replied at 2018-5-15 11:56
Everyone, how i can flashing orange pi 4G-IOT? I follow use guide from http://www.orangepi.org/downl ...

I flash my 4G-IoT with windows 7.
After debugging, I removed the J5 jumper.
But there are problems with GPIO and UART.
Not by any means fails to connect.

priapradana · Published in 2018-5-16 13:32:43

MiXaiLL76 replied at 2018-5-15 20:54
I flash my 4G-IoT with windows 7.
After debugging, I removed the J5 jumper.
But there are problems ...

must with J5 jumper? O.o if with android os, need that? thanks..

priapradana · Published in 2018-5-25 15:21:30

Some mistake in User Guide Installation Orange Pi 4G-IOT from Orange Pi. In step flashing firmware with Flash Tools in Windows, if cannot download firmware and after remove J5 jumper still cannot, because system in flashing mode just 1 second, to fast. So step e switch step f, you mush click download button first and then put USB data cable. After that you can flashing Orange Pi 4G-IOT. I hope help anyone for flashing 4G-IOT, thanks