Please select To the mobile version | Continue to access the desktop computer version

OrangePi

 Login            
 Register            
Search
Hot search: orangepi
View: 1227|Reply: 0

Android booting issue - Orange Pi Prime

[Copy link]

1

Threads

1

Posts

13

Credits

Novice

Rank: 1

Credits
13
Post time 2018-6-20 20:22:12 | Show all posts |Read mode
I am new to the orange pi...
i am using orange pi prime model....
successfully install the Android OS ...
After start the Orange Pi, displays not showing...
I check the serial out using TTL pins...it shows

bootloader  : 1000000       1000000
env         : 2000000       1000000
boot        : 3000000       1000000
system      : 4000000       60000000
verity_block: 64000000      1000000
misc        : 65000000      1000000
recovery    : 66000000      2000000
sysrecovery : 68000000      60000000
private     : c8000000      1000000
alog        : c9000000      4000000
Reserve0    : cd000000      1000000
Reserve1    : ce000000      2000000
Reserve2    : d0000000      1000000
cache       : d1000000      30000000
UDISK       : 1000000       0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
misc partition found
to be run cmd=run setargs_mmc boot_normal
read item0 copy0
Item0 (Map) magic is bad
the secure storage item0 copy0 is bad
read item0 copy1
Item0 (Map) magic is bad
the secure storage item0 copy0 == copy1, the data is good
the secure storage map is empty
no item name selinux in the map
sunxi storage read fail
no item name mac in the map
sunxi storage read fail
no item name wifi_mac in the map
sunxi storage read fail
no item name bt_mac in the map
sunxi storage read fail
no item name specialstr in the map
sunxi storage read fail
check user data form private
the user data'magic is bad
update dtb dram start
update dtb dram  end
serial is: 34005035c200282e0c4c
[      2.725]inter uboot shell
Hit any key to stop autoboot:  0
read partition: boot or recovery
[      3.449]sunxi flash read ffset 3000000, 15623416 bytes OK
Kernel load addr 0x40080000 size 11916 KiB
RAM disk load addr 0x41000000 size 2318 KiB
[      3.513]ready to boot
prepare for kernel
[mmc]: MMC Device 2 not found
[mmc]: mmc 2 not find, so not exit

Starting kernel ...



Then finally it shows....


[  269.061744] RTL871X: rtl8723bs BT-Coex version = BTCOEX20140929-5443
[  269.068726] sunxi-wlan wlan.32: bus_index: 1
[  269.073790] sunxi-wlan wlan.32: check wlan wlan_power voltage: 3300000
[  269.283222] RTL871X: rtw_ndev_init(wlan0)
[  269.322255] RTL871X: rtw_ndev_init(p2p0)
[  269.360144] RTL871X: gpio_hostwakeup_irq_thread
[  269.362517] RTL871X: module init ret=0
[  269.857704] misc sunxi-wlan: start scan device on bus_index: 1
[  269.866723] misc sunxi-wlan: start scan device on usb_index: 3
[  269.873365] hci: ERR: sunxi_ehci is already enable, can not enable again
[  269.880814] hci: ERR: sunxi_ohci is already enable, can not enable again
[  275.310392] misc sunxi-wlan: start scan device on bus_index: 1
[  275.325464] misc sunxi-wlan: start scan device on usb_index: 3
[  275.331924] hci: ERR: sunxi_ehci is already enable, can not enable again
[  275.345193] hci: ERR: sunxi_ohci is already enable, can not enable again
[  281.004671] misc sunxi-wlan: start scan device on bus_index: 1
[  281.011108] misc sunxi-wlan: start scan device on usb_index: 3
[  281.022882] hci: ERR: sunxi_ehci is already enable, can not enable again
[  281.030227] hci: ERR: sunxi_ohci is already enable, can not enable again
[  287.206648] IPv6: ADDRCONF(NETDEV_UP): p2p0: link is not ready
[  287.336634] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready



how to resolve this error?....
Anyone give solution for this...

You have to log in before you can reply Login | Register

Points Rules

Archiver|Mobile edition|Darkroom|OrangePi En ( 粤ICP备14086627号-2

2019-11-15 21:33 GMT+8 , Processed in 0.027793 second(s), 23 queries .

Powered by Discuz! X3.2

© 2014-2015 orangepibbs en.

Quick Reply To Top Return to the list