Orange pi zero 2 board can not boot ..

golvellius

Hi ..

Yesterday i have received the orangepi zero 2 board. I have tried with 3 different microsdcards .. and the results are the same.
Only in android image and using PhoenixCard app i can see the boot process from the serial port.
I am using a 5V 2A power supply.
Microsd cards .. 2GB, 4GB, and 64 gb transcend and Sandisk.

Here you have the boot output when using android image :
U-Boot 2018.05 (Oct 22 2020 - 17:24:26 +0800) Allwinner Technology

[00.507]CPU:   Allwinner Family
[00.510]Model: sun50iw9
I2C:   ready
[00.514]DRAM:  1 GiB
[00.517]Relocation Offset is: 35ec5000
[00.555]secure enable bit: 0
[00.559]pmu_axp152_probe pmic_bus_read fail
[00.563]PMU: AXP806
[00.564]PMU: pmu_axp806 found
[00.569]dcdce_vol = 3300, onoff=1
[00.572]aldo1_vol = 3300, onoff=1
[00.575]bldo1_vol = 1800, onoff=1
[00.578]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=400Mhz
[00.585]init_clocks:finish
[00.588]drv_disp_init
[00.611]HDMI 2.0 driver init start!
[00.619]__clk_enable: clk is null.
[00.622]hdmi cec clk enable failed!
[00.628]drv_disp_init finish
[00.631]gic: sec monitor mode
[00.634]boot_gui_init:start
[00.639][HDMI2.0]CEA VIC=16: [00.641]1920x1080p[00.643]@60 Hz [00.644]16:9, [00.645]8-bpp [00.647]YCbCr-444
[00.648]BT709
[00.650]eotf:SDR_LUMINANCE_RANGE
[00.765]switch device: sel=0, type=4, mode=10, format=1, bits=0, eotf=4, cs=257
[00.772]boot_gui_init:finish
[00.775]flash init start
[00.777]workmode = 17,storage type = 1
try card 2
set card number 2
get card number 2
[00.785]mmc driver ver uboot2018:2019-12-13 9:48:00
[00.789]get mem for descripter OK !
[00.794]Set eMMC Power Mode to 1.8V!
[00.798]card2 io is 1.8V.
[00.804]get card2 disable pin fail
[00.807]get sdc_ex_dly_used 2, use auto tuning sdly
[00.811]get sdc_ex_dly_used 2, use auto tuning sdly
[00.816]current is product mode, it will tune sdly later
[00.821]get sdc2 sdc_boot0_sup_1v8 fail.
[00.825]get card-pwr-gpios faild
[00.828]get card2_boot_para:time_pwroff_ms:use default time_pwroff:200
[00.834]Is not Boot mode!
[00.837]io is 1.8V
[00.838]init mmc 2 clock and io
[00.841]devnum 2, prv 7ffac860, bdesc 7c28eb6c
[00.845]SUNXI SD/MMC: 2
[00.848]==================== work mode: 17 0, sample_mode:2
[00.853]=============== start mmc_init_product...
[00.857]=============== start mmc_init_product...
[00.868]************Try SD card 2************
[00.873]rto or no error or software timeout,no need retry
[00.879]rto or no error or software timeout,no need retry
[00.884]rto or no error or software timeout,no need retry
[00.889]************Try MMC card 2************
[00.897]rto or no error or software timeout,no need retry
[00.902]Card did not respond to voltage select!
[00.906]************SD/MMC 2 init error!************
[00.911]mmc init product failed
MMC init failed
try emmc fail
nand common1 version: v1.02 2020-06-08 10:36
[00.921]NB1 : enter phy init
[00.923][NI]enter rawnand hardward init..
[00.933][ND]Reset NDFC start 0  0
[00.936][ND]Reset NDFC end 0    0
[00.939][NE]rawnand not support chip 0: 00 00 00 00 00 00 00 00
[00.945][NE]rawnand not support chip 1: 00 00 00 00 00 00 00 00
[00.950][NE]rawnand not support chip 2: 00 00 00 00 00 00 00 00
[00.956][NE]rawnand not support chip 3: 00 00 00 00 00 00 00 00
[00.962][NE]no rawnand found!
[00.964][NE]rawnand_channel_init channel@0 chips init fail
[00.969][NI]rawnand hardward init fail
[00.973][NI]---rawnand_dump_clock start---
[00.977][NI]SUNXI_CCM_BASE: 0x03001000
[00.980][NI]nand0 clk: 8300010e
[00.983][NI]nand1 clk: 8300010e
[00.986][NI]nand bus gating reset: 10001
[00.990][NI]mbus cfg: c1000002
[00.992][NI]mbus master clk gating: 25
[00.996][NI]pll_peri0 ctrl: b8003100
[00.999][NI]pll_peri1 ctrl: 88003100
[01.002][NI]---rawnand_dump_clock end---
[01.006][NI]---rawnand_dump_gpio_nand start---
[01.010][NI]SUNXI_PIO_BASE: 0x0300b000
[01.014][NI]pc cfg0: 22222222
[01.016][NI]pc cfg1: 22222222
[01.019][NI]pc cfg2 2
[01.021][NI]pc data: 0
[01.023][NI]pc drv0_lvl: 55555555
[01.026][NI]pc drv1_lvl: 1
[01.029][NI]pc pull_0: 40000440
[01.031][NI]pc pull_1: 1
[01.034][NI]voltage mode select: 0
[01.037][NI]---rawnand_dump_gpio_nand end---
[01.041][NE]nand_physic_init error -1
[01.044]NB1 : nand phy init fail
[01.047]Failed to probe nand flash
try nand fail
initcall sequence 7ff5bee0 failed at call 4a00e1fd (err=-1)
### ERROR ### Please RESET the board ###



Thanks for all ..

Waiting for recommendations ...

golvellius

Ok. Solved .. I have downloaded armbian for orangepi zero 2. Now works .

Thanks.

prborg

The armbian version only works via a serial console only...

MartinP

Please read my post from http://www.orangepi.org/orangepi ... amp;fromuid=2501169

william4882

Finally, after clearing customs, you will need to register your vehicle with the local Department of Motor Vehicles (DMV). Each state has its own registration requirements and fees https://www.youtube.com/watch?v=db-5886oHp4

kingabort

I appreciate the user-friendly design of my extension ladder, with features like quick-locking mechanisms that allow for easy setup and takedown. read this

otis

Confirm that you are pokemon infinite fusion using the correct Android image for your Orange Pi Zero 2 model. Sometimes, images designed for different models might not be fully compatible.

Heleca

Wow, this is really interesting reading. I am glad I found this and got to read it. Great job on this content. I like it.        securespend

Heleca

This is such a great resource that you are providing and you give it away for free. I love seeing blog that understand the value of providing a quality resource for free. Maharashtra Inter caste marriage scheme

Heleca

This blog website is pretty cool! How was it made !        <a href="https://www.ufa88s.info/แทงบอล/">สมัคร แทงบอล ออนไลน์</a>