8,367
edits
Changes
→26pin's SPI test
== '''How to use Win32Diskimager to burn Linux image ''' ==
1) First prepare a TF card with a capacity of 16GB or more. The transmission speed of the TF card must be class 10 or above. It is recommended to use a TF card of SanDiskand other brands<br><br>
2) Then use the card reader to insert the TF card into the computer<br><br>
c. After the image writing is completed, click the "Exit" button to exit, and then you can pull out the TF card and insert it into the development board to start<br><br>
== '''Linux system instructions ''' ==
=== Supported Linux image types and kernel versions ===
{| class="wikitable" style="width:800px;"
LMP Version: 5.1 (0xa) Subversion: 0x1111 Manufacturer: Broadcom Corporation (15)
|}
5) For the wifi connection and test method, please refer to <span style="color:#0066CC;">[[Orange Pi 5 detail#WIFI connection test | the section of WIFI connection test]]</span>, which will not be repeated here<br><br>
6) For the test method of Bluetooth, please refer to the section on Bluetooth usage, so I won’t go into details here<br><br>
[[Image:Pi-5-details-pic106.png]]<br><br>
=== 查询 HDMI 显示测试 display test ===1) 使用 Use HDMI 转 to HDMI 线连接 cable to connect Orange Pi 开发板和 development board and HDMI 显示器display<br><br>
[[Image:Pi-5-details-pic107.png]]<br><br>
2) 启动 After starting the linux 系统后如果 system, if the HDMI 显示器有图像输出说明 monitor has image output, it means that the HDMI 接口使用正常interface is working normally<br>
{| class="wikitable" style="background-color:#ffffdc;width:800px;"
|-
|注意，很多笔记本电脑虽然带有 '''Note that although many notebook computers have an HDMI''' 接口，但是笔记本的 '''interface, the HDMI''' 接口一般只有输出功能，并没有 '''interface of the notebook generally only has the output function, and does not have the function of HDMI in''' 的功能，也就是说并不能将其他设备的 ''', that is to say, the HDMIoutput of other devices cannot be displayed on the notebook screen.''' 输出显示到笔记本的屏幕上。<br>当想把开发板的 '''When you want to connect the HDMI''' 接到笔记本电脑 '''of the development board to the HDMI''' 接口时，请先确认清楚您的笔记本是支持 '''port of the laptop, please make sure that your laptop supports the HDMI infunction.''' 的功能。
|}
{| class="wikitable" style="background-color:#ffffdc;width:800px;"
|-
|当 '''When the HDMI''' 没有显示的时候，请先检查下 '''is not displayed, please check whether the HDMIcable is plugged in tightly. After confirming that there is no problem with the connection, you can change a different screen and try to see if it is displayed.''' 线有没有插紧，确认接线没问题后，可以换一个不同的屏幕试下有没有显示。
|}
=== 查询 HDMI 转 to VGA 显示测试 display test ===1) 首先需要准备下面的配件First, you need to prepare the following accessories<br>a. HDMI 转 to VGA 转换器Converter<br><br>
[[Image:Pi-5-details-pic108.png]]<br><br>
b. 一根 A VGA 线cable<br><br>
[[Image:Pi-5-details-pic109.png]]<br><br>
c. 一个支持 A monitor or TV that supports VGA 接口的显示器或者电视interface<br><br>2) HDMI 转 to VGA 显示测试如下所示display test as shown below<br><br>
[[Image:Pi-5-details-pic110.png]]<br><br>
{| class="wikitable" style="background-color:#ffffdc;width:800px;"
|-
| <br><big>'''使用 When using HDMI 转 to VGA 显示时，开发板以及开发板的 display, the development board and the Linux 系统是不需要做任何设置的，只需要开发板 system of the development board do not need to make any settings, only the HDMI 接口能正常显示就可以了。所以如果测试有问题，请检查 interface of the development board can display normally. So if there is a problem with the test, please check whether there is a problem with the HDMI 转 to VGA 转换器、VGA 线以及显示器是否有问题。converter, VGA cable and monitor.'''</big><br><br>
|}
=== 查询 HDMI 分辨率设置方法 resolution setting method ===1) 首先在 First open '''SettingsDisplay''' 中打开 in '''DisplaySettings'''<br><br>
[[Image:Pi-5-details-pic111.png]]<br><br>
2) 然后就能看到系统当前的分辨率Then you can see the current resolution of the system<br><br>
[[Image:Pi-5-details-pic112.png]]<br><br>
3) 点击 Resolution（分辨率）的下拉框，就可以看到显示器当前支持的所有分辨率Click the drop-down box of Resolution to see all resolutions currently supported by the display<br><br>
[[Image:Pi-5-details-pic113.png]]<br><br>
4) 然后选择想要设置的分辨率，再点击 Then select the resolution you want to set, and click Apply<br><br>
[[Image:Pi-5-details-pic114.png]]<br><br>
5) 等新的分辨率设置完后再选择 After the new resolution is set, select '''Keep the configuration''' 即可<br><br>
[[Image:Pi-5-details-pic115.png]]<br><br>
=== 蓝牙使用方法 How to use Bluetooth ==={| class="wikitable" style="background-color:#ffffdc;width:800px;" |-|<span style="color:#FF0000">请注意，'''Orange Pi 5''' 开发板上是没有蓝牙模块的，需要外接带蓝牙的 '''PCIe''' 网卡或者带蓝牙的 '''USB''' 网卡才能使用蓝牙功能。</span><br>外接 1.Test method of desktop image'''PCIe''' 网卡的使用说明请参考 <span style="color:#0066CC;">[[Orange Pi 5 detail#查询 AP6275P PCIe 网卡使用方法 | AP6275P PCIe 网卡的使用方法]]</span>一小节。外接 '''USB''' 网卡的使用说明请参考 <span style="color:#0066CC;">[[Orange Pi 5 detail#查询 USB 无线网卡测试 | USB 无线网卡测试]]</span>一小节。|}桌面版镜像的测试方法<br><br>1) 点击桌面右上角的蓝牙图标Click the Bluetooth icon in the upper right corner of the desktop<br><br>
[[Image:Pi-5-details-pic116.png]]<br><br>
2) 然后选择适配器Then select the adapter<br><br>
[[Image:Pi-5-details-pic117.png]]<br><br>
3) 如果有提示下面的界面，请选择 If there is a prompt on the following interface, please select '''Yes'''<br><br>
[[Image:Pi-5-details-pic118.png]]<br><br>
4) 然后在蓝牙的适配器设置界面中设置 Then set the '''Visibility Setting''' 为 to '''Always visible'''，然后关闭即可in the Bluetooth adapter setting interface, and then close it<br><br>
[[Image:Pi-5-details-pic119.png]]<br><br>
5) 然后打开蓝牙设备的配置界面Then open the configuration interface of the Bluetooth device<br><br>
[[Image:Pi-5-details-pic120.png]]<br><br>
6) 点击 Click '''Search''' 即可开始扫描周围的蓝牙设备to start scanning the surrounding Bluetooth devices<br><br>
[[Image:Pi-5-details-pic121.png]]<br><br>
7) 然后选择想要连接的蓝牙设备，再点击鼠标右键就会弹出对此蓝牙设备的操作界面，选择 '''Then select the Bluetooth device you want to connect to, and then click the right button of the mouse to pop up the operation interface of the Bluetooth device, select Pair''' 即可开始配对，这里演示的是和 to start pairing, and the demonstration here is to pair with an Android 手机配对phone<br><br>
[[Image:Pi-5-details-pic122.png]]<br><br>
8) 配对时，桌面的右上角会弹出配对确认框，选择 '''When pairing, a pairing confirmation box will pop up in the upper right corner of the desktop, just select Confirm''' 确认即可，此时手机上也同样需要进行确认to confirm, and the phone also needs to confirm at this time<br><br>
[[Image:Pi-5-details-pic123.png]]<br><br>
9) 和手机配对完后，可以选择已配对的蓝牙设备，然后右键选择 After pairing with the mobile phone, you can select the paired Bluetooth device, then right-click and select '''Send a File''' 即可开始给手机发送一张图片to start sending a picture to the mobile phone<br><br>
[[Image:Pi-5-details-pic124.png]]<br><br>
10) 发送图片的界面如下所示The interface for sending pictures is as follows<br><br>
[[Image:Pi-5-details-pic125.png]]<br><br>
=== 查询 连接 USB 鼠标或键盘测试 interface test ==={| class="wikitable" style="background-color:#ffffdc;width:800px;" |-| <br><big>'''The USB interface can be connected to a USB hub to expand the number of USB interfaces.'''</big><br><br>|}=== Connect USB mouse or keyboard to test ===1) 将 Insert the USB interface keyboard into the USB 接口的键盘插入 interface of the Orange Pi 开发板的 USB 接口中development board<br><br>2) 连接 Connect the Orange Pi 开发板到 development board to the HDMI 显示器display<br><br>3) 如果鼠标或键盘能正常操作系统说明 If the mouse or keyboard can operate normally, it means that the USB 接口使用正常（鼠标只有在桌面版的系统中才能使用）interface is working normally (the mouse can only be used in the desktop version of the system)<br><br>
=== 查询 连接 Connect USB 存储设备测试 storage device test ===1) 首先将 First insert the U 盘或者 disk or USB 移动硬盘插入 mobile hard disk into the USB interface of the Orange Pi 开发板的 USB 接口中development board<br><br>2) 执行下面的命令如果能看到 Execute the following command, if you can see the output of sdX 的输出说明 , it means that the U 盘识别成功disk is recognized successfully<br>
{| class="wikitable" style="width:800px;"
|-
|
orangepi@orangepi:~$ '''cat /proc/partitions | grep "sd*"'''
|}
3) 使用 Use the mount 命令可以将 command to mount the U 盘挂载到disk to /mnt 中，然后就能查看 , and then you can view the files in the U 盘中的文件了disk<br>
{| class="wikitable" style="width:800px;"
|-
|orangepi@orangepi:~$ '''sudo mount /dev/sda1 /mnt/'''<br>orangepi@orangepi:~$ '''ls /mnt/'''<br>
test.txt
|}
The following command can be used to mount the U disk in exfat format on the Linux system<br>{| class="wikitable" style="width:800px;"|-|orangepi@orangepi:~$ '''sudo apt-get install exfat-utils exfat-fuse'''<br>orangepi@orangepi:~$ '''sudo mount -t exfat /dev/sda1 /mnt/'''|}4) 挂载完后通过 After mounting, you can view the capacity usage and mount point of the U disk through the '''df -h 命令就能查看 U 盘的容量使用情况和挂载点''' command<br>
{| class="wikitable" style="width:800px;"
|-
|
orangepi@orangepi:~$ '''df -h | grep "sd"'''<br>
/dev/sda1 29G 208K 29G 1% /mnt
|}
=== 查询 USB 无线网卡测试 wireless network card test ===目前测试过的能用的 The usable USB 无线网卡如下所示，其他型号的 wireless network cards that have been tested so far are as follows. Please test other types of USB 无线网卡请自行测试，如果无法使用就需要移植对应的 wireless network cards by yourself. If they cannot be used, you need to transplant the corresponding USB 无线网卡驱动wireless network card driver.<br>
{| class="wikitable" style="width:800px;"
|-
| 序号 serial number || 型号 model ||
|-
| 1 || RTL8723BU <br>支持 Support 2.4G WIFI+BT4.0 || [[Image:Pi-5-details-pic126.png]]
|-
| 2 || RTL8811 <br>支持 Support 2.4G +5G WIFI || [[Image:Pi-5-details-pic127.png]]
|-
| 3 || RTL8821CU <br>支持 Support 2.4G +5G WIFI <br>支持 BT 4.2 || [[Image:Pi-5-details-pic128.png]]
|}
'''1、RTL8723BU 测试1.RTL8723BU test'''<br><br>1) 首先将 First insert the RTL8723BU 无线网卡模块插入开发板的 wireless network card module into the USB 接口中interface of the development board<br><br>2) 然后linux 系统会自动加载RTL8723BU 蓝牙和WIFI 相关的内核模块，通过 lsmod命令可以看到下面内核模块已自动加载Then the linux system will automatically load the RTL8723BU bluetooth and WIFI-related kernel modules, through the lsmod command, you can see that the following kernel modules have been automatically loaded<br>
{| class="wikitable" style="width:800px;"
|-
|}
|}
3) 通过 Through the dmesg 命令可以看到 command, you can see the loading information of the RTL8723BU 模块的加载信息module<br>
{| class="wikitable" style="width:800px;"
|-
|orangepi@orangepi:~$ '''dmesg'''
|}
4) 然后通过 Then you can see the device node of RTL8723BU WIFI through the '''sudo ifconfig''' 命令可以看到 RTL8723BU command. For the connection and test method of WIFI 的设备节点，WIFI 的连接和测试方法请参看 , please refer to <span style="color:#0066CC;">[[Orange Pi 5 detail#查询 WIFI 连接测试 connection test | the section of WIFI 连接测试connection test]]</span>一节，这里不再赘述, which will not be repeated here<br>
{| class="wikitable" style="width:800px;"
|-
ether 00:13:ef:f4:58:ae txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B)<br>
RX errors 0 dropped 0 overruns 0 frame 0<br>
TX packets 0 bytes 0 (0.0 B)<br>TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0<br>
|}
5) 然后通过 Then you can see the USB Bluetooth device through the '''hciconfig''' 命令可以看到 USB 的蓝牙设备command<br>
{| class="wikitable" style="width:800px;"
|-
BD Address: 00:13:EF:F4:58:AE ACL MTU: 820:8 SCO MTU: 255:16 DOWN<br>
RX bytes:1252 acl:0 sco:0 events:125 errors:0<br>
TX bytes:23307 acl:0 sco:0 commands:125 errors:0<br>
|}
6) 在桌面中也可以看到出现了蓝牙图标，此时蓝牙还未打开，所以会显示一个红色的 You can also see the bluetooth icon on the desktop. At this time, the bluetooth is not turned on, so a red '''<span style="color:#FF0000">x</span>'''will be displayed<br><br>
[[Image:Pi-5-details2-pic01.png]]<br><br>
7) 点击 Click '''Turn Bluetooth On''' 可以打开蓝牙to turn on Bluetooth<br><br>
[[Image:Pi-5-details2-pic02.png]]<br><br>
8) 打开蓝牙后的显示如下所示The display after turning on Bluetooth is as follows<br><br>
[[Image:Pi-5-details2-pic03.png]]<br><br>
9) 蓝牙的测试方法请参看For the test method of Bluetooth, please refer to <span style="color:#0066CC;">[[Orange Pi 5 detail#蓝牙使用方法 How to use Bluetooth | 蓝牙使用方法the section on Bluetooth usage]]</span>一节，这里不再赘述, so I won’t go into details here<br><br>
'''2、RTL8811 测试2.RTL8811 test'''<br><br>1) 首先将 First insert the RTL8811 无线网卡模块插入开发板的 wireless network card module into the USB 接口中interface of the development board<br><br>2) 然后 Then the linux 系统会自动加载 system will automatically load the kernel module related to RTL8811 WIFI 相关的内核模块，通过 , through the lsmod 命令可以看到下面内核模块已自动加载command, you can see that the following kernel module has been automatically loaded<br>
{| class="wikitable" style="width:800px;"
|-
|}
|}
3) 通过 Through the dmesg 命令可以看到 command, you can see the loading information of the RTL8811 模块的加载信息module<br>
{| class="wikitable" style="width:800px;"
|-
[ 119.500530] usbcore: registered new interface driver rtl8821cu
|}
4) 然后通过 '''Then, you can see the WIFI device node through the sudo ifconfig''' 命令可以看到 command. For the WIFI 的设备节点，WIFI 的连接和测试方法请参看 connection and test method, please refer to <span style="color:#0066CC;">[[Orange Pi 5 detail#查询 WIFI 连接测试 connection test | the WIFI 连接测试connection test section]]</span>一节，这里不再赘述, which will not be repeated here<br>
{| class="wikitable" style="width:800px;"
|-
|}
'''3、RTL8821CU 测试3.RTL8821CU test'''<br><br>1) 首先将 First insert the rtl8821cu 无线网卡模块插入开发板的 wireless network card module into the usb 接口中interface of the development board<br><br>2) 然后使用 '''Then use the lsusb''' 命令就可以看到 command to see the device information of the rtl8821cu usb wifi 模块的设备信息，请确保 USB模块没有处于 module, please make sure that the USB module is not in Driver CDROM Mode<br>
{| class="wikitable" style="width:800px;"
|-
|-
|orangepi@orangepi:~$ '''lsusb | grep "Realtek"'''<br>
Bus 002 Device 002: ID 0bda:1a2b Realtek Semiconductor Corp. RTL8188GU 802.11n WLAN Adapter '''<span style="color:#0066CC;">(Driver CDROM Mode)</span>'''<br><br>
|}
3) The linux 系统会自动加载 system will automatically load the rtl8821cu 蓝牙和 bluetooth and wifi 相关的内核模块，通过 related kernel modules, through the lsmod 命令可以看到下面内核模块已自动加载command, you can see that the following kernel modules have been automatically loaded<br>
{| class="wikitable" style="width:800px;"
|-
|}
|}
4) 通过 Through the dmesg 命令可以看到 command, you can see the loading information of the rtl8821cu 模块的加载信息module<br>
{| class="wikitable" style="width:800px;"
|-
[ 59.280119] rtl8821cu 2-1:1.2 wlx90de80521825: renamed from wlan0
|}
5) 然后通过 Then you can see the device node of rtl8821cu wifi through the '''sudo ifconfig''' 命令可以看到 rtl8821cu command. For the wifi 的设备节点，wifi 的连接和测试方法请参看 connection and test method, please refer to the section of <span style="color:#0066CC;">[[Orange Pi 5 detail#查询 WIFI 连接测试 connection test | WIFI 连接测试connection test]]</span>一节，这里不再赘述, which will not be repeated here<br>
{| class="wikitable" style="width:800px;"
|-
TX packets 0 bytes 0 (0.0 B)
|}
6) 然后通过 '''Then you can see the USB Bluetooth device through the hciconfig''' 命令可以看到 USB 的蓝牙设备command<br>
{| class="wikitable" style="width:800px;"
|-
TX bytes:23307 acl:0 sco:0 commands:125 errors:0
|}
7) 在桌面中也可以看到出现了蓝牙图标，此时蓝牙还未打开，所以会显示一个红色的 You can also see the bluetooth icon on the desktop. At this time, the bluetooth is not turned on, so a red '''<span style="color:#FF0000">x</span>'''will be displayed<br><br>
[[Image:Pi-5-details2-pic04.png]]<br><br>
8) 点击 Click '''Turn Bluetooth On 可以打开蓝牙''' to turn on Bluetooth<br><br>
[[Image:Pi-5-details2-pic05.png]]<br><br>
9) 打开蓝牙后的显示如下所示The display after turning on Bluetooth is as follows<br><br>
[[Image:Pi-5-details2-pic06.png]]<br><br>
=== 查询 USB 摄像头测试 camera test ===1) 首先需要准备一个下图所示的或者类似的支持 First, you need to prepare a USB camera that supports UVC 协议的 protocol as shown in the figure below or similar, and then insert the USB 摄像头，然后将USB 摄像头插入到 camera into the USB port of the Orange Pi 开发板的 USB 接口中development board<br><br>
[[Image:Pi-5-details2-pic07.png]]<br><br>
2) 通过 Through the v4l2-ctl 命令可以看到 command, you can see that the device node information of the USB 摄像头的设备节点信息为camera is '''/dev/video0'''<br>
{| class="wikitable" style="width:800px;"
|-
{| class="wikitable" style="width:800px;background-color:#ffffdc;"
|-
|注意 '''Note that the l in v4l2''' 中的 '''l''' 是小写字母 '''is a lowercase letter l'''，不是数字 ''', not the number 1.'''。<br><br>
|}
3) 在桌面系统中可以使用 In the desktop system, Cheese 直接打开 can be used to directly open the USB 摄像头，Cheese 打开方法如下图所示：camera. The method of opening Cheese is shown in the figure below.：<br><br>
[[Image:Pi-5-details2-pic08.png]]<br><br>
The interface after Cheese 打开 turns on the USB 摄像头后的界面如下图所示：camera is shown in the figure below：<br><br>
[[Image:Pi-5-details2-pic09.png]]<br><br>
4) 使用 Method of using fswebcam 测试 to test USB 摄像头的方法camera<br>a. 安装 Install fswebcam
{| class="wikitable" style="width:800px;"
|-
orangepi@orangepi:~$ '''sudo apt-get install -y fswebcam'''
|}
b. 安装完 After installing fswebcam 后可以使用下面的命令来拍照, you can use the following command to take pictures<br>a) -d 选项用于指定 option is used to specify the device node of the USB 摄像头的设备节点camera<br>b) --no-banner 用于去除照片的水印is used to remove the watermark of the photo<br>c) The -r 选项用于指定照片的分辨率option is used to specify the resolution of the photo<br>d) The -S 选项用设置于跳过前面的帧数option is used to set the number of previous frames to skip <br>e) ./image.jpg 用于设置生成的照片的名字和路径is used to set the name and path of the generated photo<br>
{| class="wikitable" style="width:800px;"
|-
'''--no-banner -r 1280x720 -S 5 ./image.jpg'''
|}
c. 在服务器版的 In the server version of the linux 系统中，拍完照后可以使用 system, you can use the scp 命令将拍好的图片传到Ubuntu command to transfer the taken pictures to the Ubuntu PC 上镜像观看for image viewing after taking pictures<br>
{| class="wikitable" style="width:800px;"
|-
|orangepi@orangepi:~$ '''scp image.jpg test@192.168.1.55:/home/test'''（根据实际情况修改 （ '''Modify the IP 地址和路径）address and path according to the actual situation'''）
|}
d. 在桌面版的 In the desktop version of the linux 系统中，可以通过 system, you can directly view the captured pictures through the HDMI 显示器直接查看拍摄的图片display<br>
=== 查询 在桌面系统中测试音频方法 Testing audio methods on desktop systems ===1) 首先打开文件管理器First open the file manager<br><br>
[[Image:Pi-5-details2-pic10.png]]<br><br>
2) 然后找到下面这个文件（如果系统中没有这个音频文件，可以自己上传一个音频文件到系统中）Then find the following file (if there is no audio file in the system, you can upload an audio file to the system yourself)<br><br>
[[Image:Pi-5-details2-pic11.png]]<br><br>
3) 然后选中 Then select the audio.wav 文件，右键选择使用 file, right click and select open with vlc 打开就可以开始播放to start playing<br><br>
[[Image:Pi-5-details2-pic12.png]]<br><br>
4) 换 How to switch between different audio devices such as HDMI 播放和耳机播放等不同音频设备的方法playback and headphone playback<br>a. 首先打开音量控制界面First open the volume control interface<br><br>
[[Image:Pi-5-details2-pic13.png]]<br><br>
b. 播放音频的时候，在 When playing audio, the audio device options that the '''Playbackplayback''' 中会显示播放软件可以使用的音频设备选项， 如下图所示，在这里可以设置需要播放到哪个音频设备software can use will be displayed in Playback, as shown in the figure below, where you can set which audio device to play to<br><br>
[[Image:Pi-5-details2-pic14.png]]<br><br>
=== 查询 使用命令播放音频的方法 The method of using commands to play audio ==='''1、耳机接口播放音频测试1.Headphone interface playback audio test'''<br><br>1) 首先将耳机插入开发板的耳机孔中First insert the earphone into the earphone jack of the development board<br><br>
[[Image:Pi-5-details2-pic15.png]]<br><br>
2) 然后可以通过 '''Then you can use the aplay -l''' 命令可以查看下 command to view the sound card devices supported by the linux 系统支持的声卡设备，从下面的输出可知，'''system. From the output below, we can see that card 2''' 为 is the sound card device of es8388 的声卡设备，也就是耳机的声卡设备, that is, the sound card device of the headset<br>
{| class="wikitable" style="width:800px;"
|-
<span style="color:#0066CC;">Subdevices: 1/1</span>
|}
3) 然后使用 '''Then use the aplay''' 命令播放下系统自带的音频文件，如果耳机能听到声音说明硬件能正常使用command to play the audio file that comes with the system. If the earphone can hear the sound, it means that the hardware can be used normally.<br>
{| class="wikitable" style="width:800px;"
|-
|}
'''2、HDMI 音频播放测试2.HDMI audio playback test'''<br><br>1) 首先使用 First use the HDMI 转 to HDMI 线将 cable to connect the Orange Pi 开发板连接到电视机上（其他的 development board to the TV (other HDMI 显示器需要确保可以播放音频）monitors need to ensure that they can play audio)<br><br>2) 然后查看下 Then check the serial number of the HDMI 的声卡序号，从下面的输出可以知道 sound card. From the output below, you can know that the HDMI 的声卡为 '''sound card is card 1'''<br>
{| class="wikitable" style="width:800px;"
|-
card 2: rockchipes8388 [rockchip-es8388], device 0: dailink-multicodecs ES8323.6-0010-0 [dailink-multicodecs
|}
3) 然后使用 '''Then use the aplay''' 命令播放下系统自带的音频文件，如果 command to play the audio file that comes with the system. If the HDMI 显示器或者电视能听到声音说明硬件能正常使用monitor or TV can hear the sound, it means that the hardware can be used normally<br>
{| class="wikitable" style="width:800px;"
|-
|}
=== 查询 使用命令测试录音的方法 Method of using commands to test recording ===1) 开发板上有板载 MIC，位置如下所示：There is an onboard MIC on the development board, the location is as follows：<br><br>
[[Image:Pi-5-details2-pic16.png]]<br><br>
2) 运行 Running the '''test_record.sh main''' 命令会通过板载 command will record a piece of audio through the onboard MIC 录制一段音频，然后播放到 , and then play it to HDMI 和耳机。and headphones<br>
{| class="wikitable" style="width:800px;"
|-
Playing WAVE '/tmp/test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
|}
3) 除了板载 MIC，我们还可以通过带 In addition to the onboard MIC 功能的耳机来录制音频。将带 , we can also record audio through headphones with MIC 功能的耳机插入开发板后，运行 function. After inserting the headset with MIC function into the development board, run the '''test_record.sh headset''' 命令会通过耳机录制一段音频， 然后播放到 command to record a piece of audio through the headset, and then play it to HDMI 和耳机。and the headset.<br>
{| class="wikitable" style="width:800px;"
|-
|}
=== 26 Pin 接口引脚说明 Interface Pin Description ===1) Please refer to the figure below for the order of the 26 pin interface pins on the Orange Pi 5 开发板 26 pin 接口引脚的顺序请参考下图development board<br><br>
[[Image:Pi-5-details2-pic17.png]]<br><br>
2) The functions of the 26 pin interface pins on the Orange Pi 5 开发板 26 pin 接口引脚的功能如下表所示development board are shown in the table below<br>a. 下面是 The following is the complete pin diagram of 26pin 完整的引脚图<br><br>
[[Image:Pi-5-details2-pic18.png]]<br><br>
b. 下面的表格是上面完整表格左半边部分的图，能看得清楚点The table below is the picture of the left half of the complete table above, so you can see it clearly<br><br>
[[Image:Pi-5-details2-pic19.png]]<br><br>
c. 下面的表格是上面完整表格右半边部分的图，能看得清楚点The table below is the picture of the right half of the complete table above, so you can see it clearly<br><br>
[[Image:Pi-5-details2-pic20.png]]<br><br>
{| class="wikitable" style="background-color:#ffffdc;width:800px;"
|-
| <br><big>'''上面表格中 The pwm 都标出了对应的寄存器的基地址，在查看in the above table has marked the base address of the corresponding register, which is useful when checking which pwmchip in /sys/class/pwm/中哪个 pwmchip 对应 26pin 排针中哪个 corresponds to which pwm 引脚时很有用。'''</big><br><br>|}3) pin in the 26pin 接口中总共有 17 个 GPIO 口，所有 GPIO 口的电压都是 '''3header.3v'''<br><br><br>{| class="wikitable" style="width:800px;" |-| <br><big>'''关于Linux系统使用说明更详细的资料，你可以在<span style="color:#0066CC;">[http://www.orangepi.cn/html/hardWare/computerAndMicrocontrollers/service-and-support/Orange-pi-5.html Orange Pi 5用户手册]</span>中查阅。'''</big><br><br>|} == Android 12 系统的使用说明 ===== 已支持的 Android 版本 ==={| class="wikitable" style="width:800px;"|-| Android 版本 || 内核版本|-| Android 12 || Linux5.10|-| Android 12 Box || Linux5.10
|}
3) There are a total of 17 GPIO ports in the 26pin interface, and the voltage of all GPIO ports is '''<span style="color:#FF0000">3.3v</span>'''<br><br>
=='''Instructions for the use of the android 12 system''' = Android 功能适配情况 ==== How to use the use of wireless network card ===1) At present, the USB wireless network card model that is adapted to the image is shown below：<br>
{| class="wikitable" style="width:800px;"
|-
| 功能 Chip model || Android 12 Function || Android12 BoxVID&PID || Adaptation
|-
| USB2RTL8821CU || 2.4G +5G WIFI+BT 4.0x2 2 || OK 0bda:c820 || OK'''<span style="color:#FF0000">Only support wifi, Bluetooth needs to be adapted</span>'''
|-
| USB3RTL8723BU || 2.4G WIFI+BT4.0x1 0 || OK 0bda:b720 || OK'''<span style="color:#FF0000">Only support wifi, Bluetooth needs to be adapted</span>'''
|-
|}
2) 上面三款 The picture of the above three USB 无线网卡的图片如下所示：wireless network cards is shown below：<br>a. The picture of the RTL8821CU USB 无线网卡模块的图片如下所示：wireless network card module is shown below：<br><br>
[[Image:Pi-5-details2-pic21.png]]<br><br>
b. The pictures of the RTL8723BU USB 无线网卡模块的图片如下所示：wireless network card module are shown below：<br><br>
[[Image:Pi-5-details2-pic22.png]]<br><br>
c. The picture of the RTL8811CU USB 无线网卡模块的图片如下所示：wireless network card module is shown below：<br><br>
[[Image:Pi-5-details2-pic23.png]]<br><br>
3) 以上 The test methods of the USB wireless network cards of the above 3 种型号的 USB 无线网卡的测试方法都是相同的，首先需要将 models are the same. First, insert the USB 网卡插入开发板的 network card into the USB 接口<br><br>4) 然后 WIFI 的连接和测试方法请参考 <span style="color:#0066CC;">[[Orange Pi 5 detail#WIFI 的连接测试方法 | WIFI 的连接测试方法]]</span>一节<br><br>5) 蓝牙的测试请参考<span style="color:#0066CC;">[[Orange Pi 5 detail#蓝牙的测试方法 | 蓝牙的测试方法]]</span>一节<br><br> === AP6275P PCIe 网卡的使用方法 ===1) 首先需要购买一个下图所示的 AP6275P PCIe 网卡interface of the development board, and then enter '''Setting'''<br><br>
[[Image:Pi-5-details2-pic24.png]]<br><br>
[[Image:Pi-5-details2-pic25.png]]<br><br>
[[Image:Pi-5-details2-pic26.png]]<br><br>
[[Image:Pi-5-details2-pic27.png]]<br><br>
[[Image:Pi-5-details2-pic28.png]]<br><br>
[[Image:Pi-5-details2-pic29.png]]<br><br>
[[Image:Pi-5-details2-pic30.png]]<br><br>
[[Image:Pi-5-details2-pic31.png]]<br><br>
[[Image:Pi-5-details2-pic32.png]]<br><br>
[[Image:Pi-5-details2-pic33.png]]<br><br>
[[Image:Pi-5-details2-pic34.png]]<br><br>
[[Image:Pi-5-details2-pic35.png]]<br><br>
[[Image:Pi-5-details2-pic36.png]]<br><br>
[[Image:Pi-5-details2-pic37.png]]<br><br>
[[Image:Pi-5-details2-pic38.png]]<br><br>
[[Image:Pi-5-details2-pic39.png]]<br><br>
[[Image:Pi-5-details2-pic40.png]]<br><br>
[[Image:Pi-5-details2-pic41.png]]<br><br>
[[Image:Pi-5-details2-pic42.png]]<br><br>
[[Image:Pi-5-details2-pic43.png]]<br><br>
[[Image:Pi-5-details2-pic44.png]]<br><br>
[[Image:Pi-5-details2-pic45.png]]<br><br>
[[Image:Pi-5-details2-pic46.png]]<br><br>
[[Image:Pi-5-details2-pic47.png]]<br><br>
[[Image:Pi-5-details2-pic48.png]]<br><br>
[[Image:Pi-5-details2-pic49.png]]<br><br>
[[Image:Pi-5-details2-pic50.png]]<br><br>
[[Image:Pi-5-details2-pic51.png]]<br><br>
[[Image:Pi-5-details2-pic52.png]]<br><br>
[[Image:Pi-5-details2-pic53.png]]<br><br>
[[Image:Pi-5-details2-pic54.png]]<br><br>
[[Image:Pi-5-details2-pic55.png]]<br><br>
[[Image:Pi-5-details2-pic56.png]]<br><br>
[[Image:Pi-5-details2-pic59.png]]<br><br>
[[Image:Pi-5-details2-pic60.png]]<br><br>
[[Image:Pi-5-details2-pic61.png]]<br><br>
[[Image:Pi-5-details2-pic62.png]]<br><br>