Linux Distributions for Orange PI H3 boards

derrickyee81 · Published in 2015-9-13 21:32:18

@loboris,

Million Thanks!!! i finally got it working...
Do you have a BTC acc???
I like to treat you some beer...

Cheers

loboris · Published in 2015-9-13 22:24:26

derrickyee81 replied at 2015-9-13 14:32
@loboris,

Million Thanks!!! i finally got it working...

I'm glad you've got it working.
I only have paypal account. It is on the bottom of the first post.

jacer · Published in 2015-9-13 23:58:31

Hi, loboris. The MT7601 is not working with OPI-PC. Is kernel 4.2 ready for this board?

loboris · Published in 2015-9-14 02:01:29

jacer replied at 2015-9-13 16:58
Hi, loboris. The MT7601 is not working with OPI-PC. Is kernel 4.2 ready for this board?

There is no driver for MT7601 in 3.4 kernel.
I don't expect there will be 4.2 kernel for OPI H3 boards in the near future.

jacer · Published in 2015-9-14 11:06:08

Edited by jacer at 2015-9-14 11:13

loboris replied at 2015-9-14 02:01
There is no driver for MT7601 in 3.4 kernel.
I don't expect there will be 4.2 kernel for OPI H3 bo ...

No driver for this wireless card also. Can you fix it? Is VDPAU like below link possible?
VDPAU Here is the author got MALI400 working on BPI.

Bus 004 Device 002: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter

Copy code

B.t.w. there is not a good Android firmware for OPI-PC yet, the Official version is buggy.

Vladimir55 · Published in 2015-9-14 16:53:45

Dear loboris!
I'm testing assemblies.
almost replaced raspberi pi 2!

board mini 2
OrangePI_Jessie_Xfce.img
audio -3.5mm. ok! (others "img"  could not ? )
Wi-fi st - OK!  (usb to wifi)
Wi-Fi ap - OK! (usb to wifi)
i2s -ok! (400 kHz)
SPI - ok! (50 MHz)
uart 0-2 ok! (115200)
usb to uart  ok! (921600 baud)
PWM  - has not yet been run ...

GPIO - INPUT / output - OK!
Interrupt GPIO - yet failed to start ...

wonder whether it is possible to work quickly GPIO interrupt ?
Thank you for your work!

osakanataro · Published in 2015-9-14 21:56:07

Thanks lobris !
works good!

john0815 · Published in 2015-9-14 23:42:15

Hello!

Do anyone have an idea why WLAN is not working. I Installed the latest LIB and uImage. I am using OPI Plus.
I dont know since what date this is so because I am normal on wired lan.
I tried to install apmode and there I recognized this.

ifconfig says:

eth0    Link encap:Ethernet  Hardware Adresse 5e:e3:93:4a:04:79
      inet Adresse:10.4.191.119  Bcast:10.4.191.255  Maske:255.255.255.0
      inet6-Adresse: fe80::5ce3:93ff:fe4a:479/64 Gültigkeitsbereich:Verbindung
      UP BROADCAST RUNNING MULTICAST  MTU:1500  Metrik:1
      RX-Pakete:1298 Fehler:0 Verloren:0 Überläufe:0 Fenster:0
      TX-Pakete:761 Fehler:0 Verloren:0 Überläufe:0 Träger:0
      Kollisionen:0 Sendewarteschlangenlänge:1000
      RX-Bytes:417965 (417.9 KB)  TX-Bytes:134401 (134.4 KB)
      Interrupt:114

lo       Link encap

okale Schleife
      inet Adresse:127.0.0.1  Maske:255.0.0.0
      inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
      UP LOOPBACK RUNNING  MTU:16436  Metrik:1
      RX-Pakete:476 Fehler:0 Verloren:0 Überläufe:0 Fenster:0
      TX-Pakete:476 Fehler:0 Verloren:0 Überläufe:0 Träger:0
      Kollisionen:0 Sendewarteschlangenlänge:0
      RX-Bytes:41043 (41.0 KB)  TX-Bytes:41043 (41.0 KB)

lsusb:
root@OrangePI:~# lsusb
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 05e3:0718 Genesys Logic, Inc. IDE/SATA Adapter
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 005: ID 05e3:0610 Genesys Logic, Inc. 4-port hub
Bus 002 Device 004: ID 045e:0039 Microsoft Corp. IntelliMouse Optical
Bus 002 Device 003: ID 046a:0021 Cherry GmbH CyMotion Expert Combo
Bus 002 Device 002: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@OrangePI:~#

iwconfig is not working and cannot be installed

fabrixio · Published in 2015-9-15 01:22:41

@Loboris: Are you going to add suport for wireless AP62xx?

Cheers

loboris · Published in 2015-9-15 02:05:15

Edited by loboris at 2015-9-14 19:07

john0815 replied at 2015-9-14 16:42
Hello!

Do anyone have an idea why WLAN is not working. I Installed the latest LIB and uImage. I am ...

Check if you have the right script.bin on your sd card fat partition.
If you have an "old" image, please try to install one of the new small (basic) images to see if wifi is working.
wifi adapter is not visible in lsusb.