Linux Distributions for Orange PI H3 boards

on4top · Published in 2015-10-5 06:09:14

Found another USB Wifi Dongle .. Succes !

root@OrangePI:~# lsusb
Bus 008 Device 002: ID 04d8:000a Microchip Technology, Inc. CDC RS-232 Emulation                                                                                           Demo
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 04f2:0603 Chicony Electronics Co., Ltd
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless                                                                                           Adapter
Bus 003 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@OrangePI:~#

Oct  4 21:57:08 localhost vmunix: [ 4127.150082] usb 3-1: new high-speed USB device number 9 using sunxi-ehci
Oct  4 21:57:08 localhost vmunix: [ 4127.303032] hub 3-1:1.0: USB hub found
Oct  4 21:57:08 localhost vmunix: [ 4127.303400] hub 3-1:1.0: 4 ports detected
Oct  4 21:57:08 localhost vmunix: [ 4127.580600] usb 3-1.2: new high-speed USB device number 10 using sunxi-ehci
Oct  4 21:57:08 localhost vmunix: [ 4127.800507] usb 3-1.2: reset high-speed USB device number 10 using sunxi-ehci
Oct  4 21:57:08 localhost vmunix: [ 4127.937535] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Oct  4 21:57:08 localhost vmunix: [ 4127.938754] Registered led device: rt2800usb-phy1::radio
Oct  4 21:57:08 localhost vmunix: [ 4127.938895] Registered led device: rt2800usb-phy1::assoc
Oct  4 21:57:08 localhost vmunix: [ 4127.939026] Registered led device: rt2800usb-phy1::quality
Oct  4 21:57:09 localhost vmunix: [ 4128.498129] ADDRCONF(NETDEV_UP): wlan1: link is not ready
Oct  4 21:57:11 localhost vmunix: [ 4130.784668] wlan1: authenticate with 2e:a4:3c:7d:d0:ac
Oct  4 21:57:11 localhost vmunix: [ 4130.855290] wlan1: send auth to 2e:a4:3c:7d:d0:ac (try 1/3)
Oct  4 21:57:11 localhost vmunix: [ 4130.858184] wlan1: authenticated
Oct  4 21:57:11 localhost vmunix: [ 4130.930114] wlan1: associate with 2e:a4:3c:7d:d0:ac (try 1/3)
Oct  4 21:57:11 localhost vmunix: [ 4130.935839] wlan1: RX AssocResp from 2e:a4:3c:7d:d0:ac (capab=0x431 status=0 aid=3)
Oct  4 21:57:12 localhost vmunix: [ 4131.007529] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Oct  4 21:57:12 localhost vmunix: [ 4131.007757] wlan1: associated
Oct  4 21:57:45 localhost vmunix: [ 4164.530294] PHY: gmac0-0:00 - Lin

root@OrangePI:/var/log# ifconfig
eth0    Link encap:Ethernet  HWaddr e2:95:3a:d6:56:75
      UP BROADCAST MULTICAST  MTU:1500  Metric:1
      RX packets:0 errors:0 dropped:0 overruns:0 frame:0
      TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:0 (0.0 B)  TX bytes:510 (510.0 B)
      Interrupt:114

lo       Link encap

ocal Loopback
      inet addr:127.0.0.1  Mask:255.0.0.0
      inet6 addr: ::1/128 Scope:Host
      UP LOOPBACK RUNNING  MTU:16436  Metric:1
      RX packets:19022 errors:0 dropped:0 overruns:0 frame:0
      TX packets:19022 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:0
      RX bytes:49419500 (47.1 MiB)  TX bytes:49419500 (47.1 MiB)

wlan1    Link encap:Ethernet  HWaddr 00:1f:1f:59:e9:7e
      inet addr:10.98.239.84  Bcast:10.98.239.255  Mask:255.255.255.0
      inet6 addr: fe80::21f:1fff:fe59:e97e/64 Scope

ink
      UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
      RX packets:6169 errors:0 dropped:0 overruns:0 frame:0
      TX packets:6838 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:1133686 (1.0 MiB)  TX bytes:6588118 (6.2 MiB)

hhrhhr · Published in 2015-10-5 06:13:22

Edited by hhrhhr at 2015-10-5 06:16

loboris replied at 2015-10-5 03:58
I think the kernel sources archive kernel_3.4.9.tar.xz is clean

archive contain ~1 Gb of *.o and ~400 Mb of temp files.

I don't understand your comment about "сurrent script" ...

from last make_linux.tar.gz archive. but I'm sorry, I was a bit mistaken, install (or not install) openssh actually has nothing to do with the choice of locale.

loboris · Published in 2015-10-5 07:02:28

Edited by loboris at 2015-10-5 00:06

hhrhhr replied at 2015-10-4 23:13
archive contain ~1 Gb of *.o and ~400 Mb of temp files.

if ONLY_BASE="yes" the script creates minimal working image, you can install shh later.
params.sh:

# *****************************************************
# Set to "yes" to create realy minimal image *
# *****************************************************
ONLY_BASE="no"

Yu are right about kernel_3.4.9.tar.xz, I'll upload new sources with latest changes (this time clean) soon.

Survive-Pi · Published in 2015-10-5 08:28:33

loboris replied at 2015-10-4 13:11
I don't quite understand your problem.
If you installed Debian xfce image (according to the instru ...

The giant heatsink is what I found in an old laptop. Free, handy, covered all three chips.

Does not get to the graphical login screen.

Survive-Pi · Published in 2015-10-5 08:42:04

Edited by Survive-Pi at 2015-10-4 17:47

Sorry you can't see top or left edge...can't get any images down to actual screen size. No resize options in it's menu...That is a still shot of the video that I was able to catch the one frame of what flashed past between entering login and password...

Windows 10 laptop.
Download and extract newest Debian xfce image.
burn image with win32diskimager.
Remove and reinsert card.
Rename *.img.opiplus to *.img
Rename script.bin_*plus1080p60 to script.bin
Insert in Pi Plus board...above pic is result.

Raspian img from resources boots without monitor...
Tried other loboris imgs with same results as above.
Will try a different sd card.

Survive-Pi · Published in 2015-10-5 11:05:25

Board will not boot new image.
Step 1- Confirm correct/adequate power supply. check
Step 2- Double check your work creating uimage. quadruple checked
Step 3- Try a different SD card. success!!!!!!

Would that explain why the raspian image in downloads didn't work?

Thank you loboris. Thinking out my last reply to you gave me the idea...

Sent from Orange Pi Plus running loboris Debian 8 xfce.

jacer · Published in 2015-10-5 11:28:32

loboris replied at 2015-9-30 02:11
If the drivers for some devices are not in the kernel source, I can't do anything about it. If you ...

I am using your Lubuntu 15.04 and x2go with custom command below but cannot start desktop session. It reports "session start failed" error. Have you tried? I am using the PyHoca-GUI 0.5.0.4 which is the newest version.
lxsession -s Lubuntu -e LXDE

jacer · Published in 2015-10-5 12:56:00

Can you build driver for this card? The source code can be download from here.
http://12244.wpc.azureedge.net/8 ... 2_9000.20130911.zip
I need android 4.2.2 and 4.4.2 driver (ko file) also.

lukish · Published in 2015-10-5 13:13:49

lukish replied at 2015-10-4 22:15
Sorry, I can test in 6 hours. Will definitely report the results. While far away I was from the Bo ...

Well, arduino is now working, well everything else I need too. Thank you very much.

jacer · Published in 2015-10-5 14:27:34

MT7601 source code and instruction can be found http://blog.csdn.net/zqj6893/article/details/44258439.

Linux Distributions for Orange PI H3 boards

This thread contains more resources

Viewed section