All Oranges, Debian and Ubuntu images, updated 12.1.2019

igorpec · Published in 2016-2-18 19:33:10

kevinheb replied at 2016-2-18 08:07
Hi there, I have tried copying the image in Windows and Linux. When I insert the card into the pi a ...

I only have Orange Plus here and the red light come up when kernel loads, so little later as well ethernet lights.I have no idea how leds are operating on other boards but system should boot if you made images correctly.

http://www.armbian.com/documentation/

Just write an image to SD card, nothing else is needed.

We might switch to old stock uboot (if things will work ok) next week so it will be as usuall, with HDMI out and everything.

igorpec · Published in 2016-2-18 20:50:50

HDMI fixed on all H3 images.

pmos69 · Published in 2016-2-19 09:17:25

igorpec replied at 2016-2-18 20:50
HDMI fixed on all H3 images.

You move fast.
Now I have to check it.
Building...

Thanks

igorpec · Published in 2016-2-19 14:00:54

Yes, we made a lot of progress in last few days

One major issue was also solved - we now have one common kernel for all Oranges. Kernel is soon going to repository (apt.armbian.com) which brings updating via apt-get upgrade. Soon.

Next is configuration expand and fixes.

rufik · Published in 2016-2-19 18:20:28

Will armbian support Orange Pi 2? I think it's the same as Pi PC but with wifi built-in.

igorpec · Published in 2016-2-19 19:03:23

It's already supported - we just haven't build the image yet since nobody around has it to test.

rufik · Published in 2016-2-19 19:34:04

I have one and I could test

Just build it and share a link, please.

igorpec · Published in 2016-2-19 21:31:10

Edited by igorpec at 2016-2-19 14:43

http://www.armbian.com/orange-pi-2/

Debian Jessie, root / 1234

y52 · Published in 2016-2-19 21:50:32

Edited by y52 at 2016-2-19 21:51

Hello, I set the
Debian Jessie, root / 1234
http://www.armbian.com/orange-pi-plus/

on my OPI+. Much to my regret, the Ethernet port is not initialised and I am unable to access the board from outside.
The ethernet module is not loaded and the network LEDs are not blinking.
What should be done to make it run?

dmesg show:
gmac0: eth0 initialize hardware error

At the same time, how could the X-system be brought up?
The startx is not found on this system.

y52 · Published in 2016-2-19 22:43:18

To complete the above experience with OPi+ here is the lsmod output:
[root@karma home]# cat lsmod.160218.txt
Module                Size  Used by
rtl8187             48600  0                   <- an extra dongle
eeprom_93cx6          2375  1 rtl8187
mac80211             366795  1 rtl8187
w1_therm             2506  0
w1_gpio                1402  0
wire                18333  2 w1_gpio,w1_therm
w1_sunxi             1451  0
gpio_sunxi             8253  0
8189es             896688  0

There is no ethernet module loaded above.
The dmesg shows:
[ 9.340170] gmac0 gmac0: eth0: eth0: PHY ID 00000000 at 0 IRQ poll (gmac0-0:00)
[ 9.350363] gmac0 gmac0: eth0: Initialize hardware error

What's wrong?

The full dmesg is could not be fit into this message, but it is available.

[ 0.545634] usbcore: registered new interface driver ums-realtek
[ 0.545683] usbcore: registered new interface driver ums-sddr09
[ 0.545732] usbcore: registered new interface driver ums-sddr55
[ 0.545782] usbcore: registered new interface driver ums-usbat
[ 0.545913] usbcore: registered new interface driver usbserial
[ 0.545924] usbserial: USB Serial Driver core
[ 0.545975] usbcore: registered new interface driver option
[ 0.546018] USB Serial support registered for GSM modem (1-port)
[ 0.546555] file system registered
[ 0.548230] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 0.548245] android_usb gadget: Number of LUNs=3
[ 0.548258]  lun0: LUN: removable file: (no medium)
[ 0.548269]  lun1: LUN: removable file: (no medium)
[ 0.548280]  lun2: LUN: removable file: (no medium)
[ 0.548614] android_usb gadget: android_usb ready
[ 0.548831]  uinput result 0 , vmouse_init
[ 0.549442] mousedev: PS/2 mouse device common for all mice
[ 0.549695] ls_fetch_sysconfig_para: type err  device_used = 0.

[ 0.563285] sunxi_leds_fetch_sysconfig_para script_parser_fetch "leds_para" leds_used = -284672164
[ 0.563299] =========script_get_err============
[ 0.564896] usbcore: registered new interface driver usbhid
[ 0.564907] usbhid: USB HID core driver

[ 0.614307] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[ 0.617453] [rf_pm]: select module num is 7
[ 0.617468] [rf_pm]: module power0 name vcc-wifi-33
[ 0.617479] [rf_pm]: failed to fetch module_power1
[ 0.617490] [rf_pm]: mod has no chip_en gpio
[ 0.617499] [rf_pm]: failed to fetch lpo_use_apclk
[ 0.617507] [rf_pm]: regulator on.
[ 0.617799] [wifi_pm]: wifi gpio init is OK !!
[ 0.617857] [rfkill]: init no bt used in configuration

[ 2.285557] mmc2: new high speed DDR MMC card at address 0001
[ 2.286461] mmcblk1: mmc2:0001 M8G1GC 7.28 GiB
[ 2.286962] mmcblk1boot0: mmc2:0001 M8G1GC partition 1 4.00 MiB
[ 2.287425] mmcblk1boot1: mmc2:0001 M8G1GC partition 2 4.00 MiB
[ 2.289393]  mmcblk1: p1 p2 p3 < p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 >
[ 2.289458] mmcblk1: p1 size 10412032 extends beyond EOD, truncated
[ 2.298331]  mmcblk1boot1: unknown partition table
[ 2.301329]  mmcblk1boot0: unknown partition table
[ 2.301942] *******************mmc init ok *******************
[ 2.318012] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
[ 2.318117] VFS: Mounted root (ext4 filesystem) on device 179:1.
[ 2.334893] devtmpfs: mounted
[ 2.335610] Freeing init memory: 320K
[ 3.500552] systemd[1]: systemd 215 running in system mode. (+PAM +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ -SECCOMP -APPARMOR)
[ 3.501120] systemd[1]: Detected architecture 'arm'.
[ 3.526348] systemd[1]: Set hostname to <orangepiplus>.
[ 4.473865] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.

[ 4.483202] systemd[1]: Starting system-getty.slice.
[ 4.483626] systemd[1]: Created slice system-getty.slice.
[ 4.483742] systemd[1]: Starting Increase datagram queue length...
[ 4.590566] systemd[1]: Starting Restore / save the current clock...
[ 4.691042] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 4.760836] systemd[1]: Mounted POSIX Message Queue File System.
[ 4.760956] systemd[1]: Starting udev Coldplug all Devices...
[ 4.811109] systemd[1]: Started Set Up Additional Binary Formats.
[ 4.811478] systemd[1]: Mounting Debug File System...
[ 4.886955] systemd[1]: Starting Load Kernel Modules...
[ 4.940749] systemd[1]: Mounted Huge Pages File System.
[ 4.940898] systemd[1]: Starting LSB: Set keymap...
[ 5.020593] systemd[1]: Starting Slices.
[ 5.021075] systemd[1]: Reached target Slices.
[ 5.023464] systemd[1]: Mounted Debug File System.
[ 5.086819] RTL871X: module init start
[ 5.086834] RTL871X: rtl8189es v4.3.0.4_11916.20140724_COB
[ 5.086843] RTL871X: build time: Feb 18 2016 13:28:39
[ 5.086858] [wifi_pm]: set wl_reg_on 0 !
[ 5.090680] systemd[1]: Started Increase datagram queue length.
[ 5.136911] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B

[ 5.190576] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 5.246051] [wifi_pm]: set wl_reg_on 1 !
[ 5.252770] bFWReady == _FALSE call reset 8051...
[ 5.274838] bFWReady == _FALSE call reset 8051...
[ 5.296308] bFWReady == _FALSE call reset 8051...
[ 5.319660] RTL871X: rtw_ndev_init(wlan0)
[ 5.320879] RTL871X: rtw_ndev_init(wlan1)
[ 5.322076] RTL871X: module init ret=0
[ 5.328818] gpio_pin_1(362) gpio_request
[ 5.328983] gpio_pin_2(15) gpio_request
[ 5.329075] gpio_pin_3(6) gpio_request
[ 5.329164] gpio_pin_4(13) gpio_request
[ 5.329256] gpio_pin_5(14) gpio_request
[ 5.329348] gpio_pin_6(110) gpio_request
[ 5.329442] gpio_pin_7(3) gpio_request
[ 5.329528] gpio_pin_8(68) gpio_request
[ 5.329617] gpio_pin_9(71) gpio_request
[ 5.329705] gpio_pin_10(67) gpio_request
[ 5.329794] gpio_pin_11(21) gpio_request
[ 5.329881] gpio_pin_12(7) gpio_request
[ 5.329969] gpio_pin_13(8) gpio_request
[ 5.330103] gpio_pin_14(200) gpio_request
[ 5.330198] gpio_pin_15(9) gpio_request
[ 5.330286] gpio_pin_16(10) gpio_request
[ 5.330376] gpio_pin_17(201) gpio_request
[ 5.330469] gpio_pin_18(198) gpio_request
[ 5.330561] gpio_pin_19(199) gpio_request
[ 5.330705] gpio name is PL10, ret = 0
[ 5.330861] gpio name is PA15, ret = 0
[ 5.330976] gpio name is PA6, ret = 0
[ 5.331094] gpio name is PA13, ret = 0
[ 5.331211] gpio name is PA14, ret = 0
[ 5.331330] gpio name is PD14, ret = 0
[ 5.331443] gpio name is PA3, ret = 0
[ 5.331558] gpio name is PC4, ret = 0
[ 5.331671] gpio name is PC7, ret = 0
[ 5.331791] gpio name is PC3, ret = 0
[ 5.331903] gpio name is PA21, ret = 0
[ 5.332027] gpio name is PA7, ret = 0
[ 5.332156] gpio name is PA8, ret = 0
[ 5.332272] gpio name is PG8, ret = 0
[ 5.332403] gpio name is PA9, ret = 0
[ 5.332524] gpio name is PA10, ret = 0
[ 5.332644] gpio name is PG9, ret = 0
[ 5.332756] gpio name is PG6, ret = 0
[ 5.332859] gpio name is PG7, ret = 0
[ 5.332996] gpio_init finish with uesd 1!
[ 5.338363] W1_SUNXI: Added w1-gpio on GPIO-20
[ 5.344823] Driver for 1-wire Dallas network protocol.
[ 6.049265] systemd-udevd[114]: starting version 215
[ 7.136415] EXT4-fs (mmcblk0p1): re-mounted. Opts: data=writeback,commit=600,errors=remount-ro
[ 7.368086] Adding 131068k swap on /var/swap.  Priority:-1 extents:1 across:131068k SS
[ 8.777767] systemd-journald[111]: Received request to flush runtime journal from PID 1
[ 9.339938] gmac0: probed
[ 9.340170] gmac0 gmac0: eth0: eth0: PHY ID 00000000 at 0 IRQ poll (gmac0-0:00)
[ 9.350363] gmac0 gmac0: eth0: Initialize hardware error
[  127.870105] usb 2-1.2: new high-speed USB device number 5 using sunxi-ehci
[  128.406955] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[  128.407948] ieee80211 phy2: hwaddr 00:22:3f:da:7f:3e, RTL8187BvE V0 + rtl8225z2, rfkill mask 2
[  128.429472] rtl8187: Customer ID is 0x00
[  128.429654] Registered led device: rtl8187-phy2::radio
[  128.429778] Registered led device: rtl8187-phy2::tx
[  128.429933] Registered led device: rtl8187-phy2::rx
[  128.430729] rtl8187: wireless switch is on
[  128.430982] usbcore: registered new interface driver rtl8187
[  283.883386] ADDRCONF(NETDEV_UP): wlan2: link is not ready
[  326.240408] ==> rtl8188e_iol_efuse_patch
[  326.528486] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  334.210124] RTL871X: nolinked power save enter
[  365.415247] gmac0: probed
[  365.415362] gmac0 gmac0: eth0: eth0: PHY ID 00000000 at 0 IRQ poll (gmac0-0:00)
[  365.425557] gmac0 gmac0: eth0: Initialize hardware error