Openelec Build for OPI PC and 2 now with HW decoding

jernej · Published in 2016-2-26 06:20:28

thc013 replied at 2016-2-25 18:30
the 1 cpu 100% bug from systemd or cma is still there

compiled again from scratch and it is still ...

Ok, maybe there is a problem with boot parameters. Can you check the contents of /proc/cmdline? There should be "noram" at the end. If it's not, kswapd will go to 100%.

jernej · Published in 2016-2-26 06:29:37

Demetris replied at 2016-2-25 14:05
Latest source doesn’t compile

OpenELEC-OPi2/build.OpenELEC-H3.arm-7.0-devel/media_build-66f4030/v4 ...

I tried it again and it works for me. Did you try a clean compile?

jernej · Published in 2016-2-26 06:43:14

andrejb replied at 2016-2-24 20:29
and if working with hdmi maybe the dts-ma and truehd passthrought ;)

i checked the sources but i ...

Kernel sources? Check storage/ folder. Then create a patch and put it in projects/H3/patches/linux.

jernej · Published in 2016-2-26 06:45:12

nightflasher replied at 2016-2-24 23:59
dmesg output after:
rmmod mt7601Usta
[ 7586.523900] usbcore: deregistering interface driver rt2870 ...

Ok, when I ask for dmesg output I mean complete output. I already get the important information anyway.

Galeots · Published in 2016-2-26 07:07:41

help for enable lcd with i2c HD44780 for openelec

jeevasv · Published in 2016-2-26 09:29:42

Ok I updated the builds at the same location.

Jernej, Please modify the build date to 24-02-2016 in the sticky thread.

jeevasv · Published in 2016-2-26 09:33:09

Edited by jeevasv at 2016-2-26 10:56

Galeots replied at 2016-2-26 07:07
help for enable lcd with i2c HD44780 for openelec

Everything is enabled and works properly. Just connect it to the i2c bus and Install the XBMC LCDProc addon from repository.

Depending on your i2c module you may need to copy and tweak the LCDProc conf module a little. Attached the conf file that I use. Copy it to the /storage/.config/ folder(.config folder in the second partition if you are doing it from PC)

Pay attention to the below section in file:

#Additional PCF8574T settings

i2c_line_RS=0x01
i2c_line_RW=0x02
i2c_line_EN=0x04
i2c_line_BL=0x08
i2c_line_D4=0x10
i2c_line_D5=0x20
i2c_line_D6=0x40
i2c_line_D7=0x80
BacklightInvert=yes

Demetris · Published in 2016-2-26 13:38:03

Make clean then start the compile. Do I miss anything?

jernej · Published in 2016-2-26 14:06:45

Demetris replied at 2016-2-26 06:38
Make clean then start the compile. Do I miss anything?

It's better if you just delete build directory.

Dima · Published in 2016-2-26 20:16:53

Edited by Dima at 2016-2-27 04:28

Build with all the commits till the 26st (till commit 8189147) -- OrangepiPC
https://mega.nz/#F!Lw5TBAwC!osUTNIj9zsPw2WFtttdZRA

Openelec Build for OPI PC and 2 now with HW decoding

This thread contains more resources