Linux Distributions for Orange PI H3 boards

markwinger

Is the resume_head.o an expected/acceptable error?

There is no linux-3.4/arch/boot directory.  A tar -tfv does not show this directory in the h3-lichee* or liche* gz files.  Should there be one, or does that need to be manually created?

Mark

derrickyee81

@loboris,

Sorry but can you include AP mode for your next release??? Ok still can't get it working...

If any m8 managed to get it working, please share... Thanks

moinejf

markwinger replied at 2015-6-27 22:18
Still no success on building my own kernel. Just trying to build the source modified with your chang ...

I am also generating my own kernel with gcc 4.9.2 on a ARM machine and there are a lot of problems:
ia64 binary (@loboris thanks for the brom directory), section mismatch errors, relocation problem with 2G/2G memory, Makefile errors with out-of-tree building ...
I will give the source patches as soon as I have a working kernel.

roblad

Hi,

I am trying and trying to run FTDI and may be someone can recognize a problem, when I tried to start through modprobe I have such info:

/sbin/rmmod
root@orangepi:~# /sbin/rmmod ftdi_sio
rmmod: ERROR: Module ftdi_sio is builtin.
root@orangepi:~# modprobe ftdi_sio vendor=0x0403 product=0x6001
modprobe: ERROR: ../libkmod/libkmod.c:507 kmod_lookup_alias_from_builtin_file() could not open builtin file '/lib/modules/3.4.39/modules.builtin.bin'
root@orangepi:~#

Petr

loboris replied at 2015-6-25 13:02
I don't know what could be the problem with mounting sata drive from fstab.
If you don't need it e ...

Thank you.

I think that Plex is problem. It use a lot of system resources. It crashes while I am playing movie from it, sync or randomly. Could someone please test the Plex Media Server on loboris Debian? Can be installed from http://www.htpcguides.com/instal ... lubuntu-and-debian/ where is "Install Plex Media Server on ODROID using Repository". I used it on Raspberry Pi 2 without any problems (wheezy version).


Last thing, loboris, could you please prepare Ubuntu Server for orange pi plus? It is possible? http://www.ubuntu.com/download/server/arm

Thank you very much.

Best regards,
Petr

loboris

roblad replied at 2015-6-28 15:42
Hi,

I am trying and trying to run FTDI and may be someone can recognize a problem, when I tried to  ...

FTDI and other USB serial modules are buit in my kernel, no need for insmod, just plug in:

[   49.020404] usb 2-1.2: new full-speed USB device number 5 using sunxi-ehci
[   49.201918] usbcore: registered new interface driver ftdi_sio
[   49.202014] USB Serial support registered for FTDI USB Serial Device
[   49.202479] ftdi_sio 2-1.2:1.0: FTDI USB Serial Device converter detected
[   49.202654] usb 2-1.2: Detected FT232RL
[   49.202665] usb 2-1.2: Number of endpoints 2
[   49.202676] usb 2-1.2: Endpoint 1 MaxPacketSize 64
[   49.202686] usb 2-1.2: Endpoint 2 MaxPacketSize 64
[   49.202696] usb 2-1.2: Setting MaxPacketSize 64
[   49.203468] usb 2-1.2: FTDI USB Serial Device converter now attached to ttyUSB0
[   49.203544] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
orangepi@OrangePI:~$

Example on minimal ubuntu vivid.

loboris

Petr replied at 2015-6-29 02:58
Thank you.

I think that Plex is problem. It use a lot of system resources. It crashes while I am p ...

There is nothing special to prepare for Ubuntu Server. Take the minimal image and install the server packages you need ...

loboris

derrickyee81 replied at 2015-6-28 10:30
@loboris,

Sorry but can you include AP mode for your next release??? Ok still can't get it working. ...

I think AP can work on OrangePI. There are many tutorials how to set it up. For now I have very little free time to test it, sorry. Maybe next week.

roblad

Hi,

But I tried many imgs from mega on OPI+ only base vivid starts but FTDI does not work.
Ater plug:

usb2-1.4 device not accepting addres 10, error -32   ...  -71 Unable to enumerate etc.

[   30.941129] usb 5-1.4: new full-speed USB device number 4 using sunxi-ohci
[   36.415131] usb 5-1.4: USB disconnect, device number 4
[   36.751125] usb 5-1.4: new full-speed USB device number 5 using sunxi-ohci
[   37.983133] usb 5-1.4: USB disconnect, device number 5
[   41.501127] usb 5-1.4: new full-speed USB device number 6 using sunxi-ohci
[   43.071132] usb 5-1.4: USB disconnect, device number 6
[  425.150385] usb 5-1.4: new full-speed USB device number 7 using sunxi-ohci
[  425.614402] hub 5-1:1.0: unable to enumerate USB device on port 4
[  448.860940] usb 5-1.3: new full-speed USB device number 9 using sunxi-ohci
[  449.114946] hub 5-1:1.0: unable to enumerate USB device on port 3
[  449.580931] usb 5-1.3: new full-speed USB device number 10 using sunxi-ohci
[  459.832781] usb 5-1.3: USB disconnect, device number 10
[  461.320768] usb 5-1.3: new full-speed USB device number 11 using sunxi-ohci
[  461.840755] usb 5-1.3: new full-speed USB device number 12 using sunxi-ohci
[  462.360734] usb 5-1.3: new full-speed USB device number 13 using sunxi-ohci
[  462.870735] usb 5-1.3: new full-speed USB device number 14 using sunxi-ohci
[  463.312742] hub 5-1:1.0: unable to enumerate USB device on port 3
[  467.960638] usb 5-1.3: new full-speed USB device number 15 using sunxi-ohci
[  468.214643] hub 5-1:1.0: unable to enumerate USB device on port 3
[  469.630852] usb 5-1.3: new full-speed USB device number 16 using sunxi-ohci
[  469.884620] hub 5-1:1.0: unable to enumerate USB device on port 3
[  470.210599] usb 5-1.3: new full-speed USB device number 17 using sunxi-ohci
[  470.770601] usb 5-1.3: new full-speed USB device number 18 using sunxi-ohci
[  471.330582] usb 5-1.3: new full-speed USB device number 19 using sunxi-ohci
[  471.870575] usb 5-1.3: new full-speed USB device number 20 using sunxi-ohci
[  472.310608] hub 5-1:1.0: unable to enumerate USB device on port 3
[  479.930456] usb 5-1.3: new full-speed USB device number 21 using sunxi-ohci
[  480.470436] usb 5-1.3: new full-speed USB device number 22 using sunxi-ohci
[  481.010436] usb 5-1.3: new full-speed USB device number 23 using sunxi-ohci
[  481.550408] usb 5-1.3: new full-speed USB device number 24 using sunxi-ohci
[  481.990447] hub 5-1:1.0: unable to enumerate USB device on port 3
[  482.920398] usb 5-1.3: new full-speed USB device number 25 using sunxi-ohci
[  486.840338] usb 5-1.3: USB disconnect, device number 25
[  496.441185] usb 5-1.3: new full-speed USB device number 26 using sunxi-ohci
[  507.256027] usb 5-1.3: USB disconnect, device number 26
[  511.290967] usb 5-1.4: new full-speed USB device number 27 using sunxi-ohci

Arduino shows nothing as well

jslav

I Build kernel from the latest sources:
Building sequence is:

1. Extract sources

1. > mkdir sandbox
   
2. > cd sandbox
   
3. > tar xvzf ../h3-lichee-1.0.tar.gz # got [b]lichee[/b] directory
   
4. > cd lichee
   
5. > tar xvzf ../../lichee.tar.gz # kind of patch. Files from ../../lichee.tar.gz are copied to linux-3.4 directory
   

Copy code

>

2. Build sources AS IS
>./build_linux_kernel.sh
The fiirst error message happens here:

1.   CC      arch/arm/mach-sunxi/power/brom/resume_head.o
   
2. arm-linux-gnueabi-gcc: error: unrecognized command line option ‘--min_array_alignment=4’
   
3. arm-linux-gnueabi-gcc: error: unrecognized command line option ‘--no_unaligned_access’
   
4. make[3]: *** [arch/arm/mach-sunxi/power/brom/resume_head.o] Error 1
   
5. make[2]: *** [arch/arm/mach-sunxi/power/brom/resumes.code] Error 2
   
6. make[1]: *** [arch/arm/mach-sunxi/power] Error 2
   
7. make[1]: *** Waiting for unfinished jobs....
   
8.   CC      ipc/util.o
   
9.   CC      security/commoncap.o
   
10. make: *** [arch/arm/mach-sunxi] Error 2
    
11. make: *** Waiting for unfinished jobs....
    

Copy code

What is wrong?
Why command line options ‘--min_array_alignment=4’ and ‘--no_unaligned_access’ can be unrecognized?